Marantz SR6003 English, Connecting Digital Audio Components, Connecting Audio Components, Others

ENGLISH

NAMESAND FUNCTION

CONNECTING AUDIO COMPONENTS

L

L

Tape Deck

CD recorder

OUT IN

BASIC CONNECTIONS

R

R

OUT IN

DIGITAL

L

DIGITAL

L

R

L

R

L INPUT

OUTPUT

R

R

L R

R L

L

R

L

R

BASIC

INPUT 1(TV)

VIDEO

FM

ANTENNA

(75Ω)

GND

AM

INPUT 1(TV)

INPUT 2(DVD)

INPUT 3(VCR)

OUTPUT 1

OUTPUT 2

OPERATION

S-VIDEO

AUDIO

TV(1)

DVD(2)

VCR IN(3) VCR OUT

DSS(4) MONITOR OUT

Y

CB/PB CR/PR

L

SL

C

SBL

ZONE A TV

DVD

VCR

DSS

TAPE

CD/CDR

DIGITAL IN DIGITAL

FLASHER IN REMOTE CONT.

INPUT 2(DVD)

REC/ZONE B

SIRIUS

L

IN

4

5

R

R

SR

SW

SBR

OUT

IN

OUT

IN

OUT

IN OUT

1

2

3

OUT

DC OUT OUT

(AUX 2)

7.1CH INPUT

RS-232C

SPEAKER C

AC OUTLETS

ADVANCED CONNECTIONS

OFF ON

120V

60Hz

L

SL

C

SBL

R

L

R

L

R

L

R

L

UNSWITCHED

1.25A 150W

FRONT A

FRONT B

SURROUND

CENTER

SURROUND BACK

SWITCHED

AC

R

SR

SW

SBR

FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS

SPEAKER C/

1.25A 150W

FRONT A + B : 8 OHMS

SPEAKER SYSTEMS

ZONE SPEAKER A

PRE OUT

R L

R L

SETUP

ADVANCED OPERATION

Analog Audio

R

L

TROUBLESHOOTING

Digital Audio (coaxial)

Digital Audio (optical)

OTHERS

The output audio signal from the TAPE OUT jack and the CD/CD RECORDER OUT jack is the same signal which is currently selected.

Caution:

•Do not connect this unit and other components to mains power until all connections between components have been completed.

Notes:

•Insert all plugs and connectors securely. Incomplete connections may make noise.

•Be sure to connect the left and right channels properly.

Red connectors are for the R (right) channel, and white connectors are for the L (left) channel.

•Be sure to connect input and output properly.

•Refer to the instructions for each component that is connected to this unit.

•Do not bind audio/video connection cables with power cables and speaker cables this will result in generating a hum or other noise.

CONNECTING DIGITAL AUDIO COMPONENTS

•There are 5 digital inputs, 2 coaxial jacks and 3 optical jacks, on the rear panel. You can use these jacks to input PCM, Dolby Digital and DTS bitstream signals from a CD, DVD, or other digital source components.

•There is one optical output jack on the rear panel. This jack can be connected to a CD recorder or a MD recorder input.When you use this jack as ZONE B, you cannot use it as recording output. (See page 9, 38)

•Refer to the instructions for each component. To setup the digital audio format of DVD player, or other digital source’s connected to digital input jacks.

•Use fi ber optical cables (optical) for DIG-1,2,3 input jacks and REC/ZONE B output jack. Use 75 ohms coaxial cables (for digital audio or video) for DIG-4, 5 input jacks.

•You can designate the input for each digital input/ output jacks according to your component. (See page 27)

Notes:

•The digital signal jacks on this unit conform to the EIA standard. If you use a cable that does not conform to this standard, this unit may not function properly.

•Each type of audio jack works independently. Signals input through the digital and analog jacks are output through the corresponding digital and analog jacks, respectively.

12