TV AUTO ON/OFF FUNCTION
This function allows the component connected to the
AUTO POWER ON
1. Be sure the TV auto mode is Enabled. (Refer to page 37:)
2. Connect your TV TUNER (etc) to the TV- VIDEO in terminal. Be sure to connect the VIDEO input.
3. Turn OFF the power to the TV TUNER and turn standby to the unit.
4. Turn ON the TV TUNER and tune in a receivable station.
5.
AUTO POWER OFF
1. In the above situation, turn the TV TUNER OFF or select a channel that does not contain any broadcast.
2. The power to the unit switches to STANDBY after approx. 5 minutes.
Notes:
•AUTO POWER OFF is canceled if this unit is set to a source other than TV.
The function reactivates when TV is selected again.
•Some TV broadcasts may cause the TV AUTO FUNCTION to turn ON.
•The
•This function is inactive when STANDBY MODE is set to ECONOMY. To use this function, set STANDBY MODE to NORMAL.
LIP.SYNC
Depending on the image device (TV, monitor, projector, etc.) connected to the unit a time lag can occur between image signal processing and audio signal processing. Though minor, this time lag can interfere with movie and music enjoyment. The LIP. SYNC feature delays the audio signal with respect to the image signal output from the unit to correct the time lag between the sound and image. It can be operated with the “LIP SYNC” and 1 and 2 cursor buttons of the remote controller. Set the remote controller to the AMP mode before operating the LIP.SYNC feature. The initial setting is OFF (0 ms). The time lag can be adjusted in 10 ms steps up to 200 ms.
Watch the picture on the image device (i.e., TV, monitor, projector, etc.) as you adjust the time lag.
Note:
•The LIP.SYNC feature turns OFF (0 ms) in the SOURCE/PURE DIRECT mode. When the SOURCE/PURE DIRECT mode is deactivated, the set value of the LIP.SYNC feature is automatically restored.
•Even if you do not correct the time lag manually this way, audio and video are automatically synchronized when the unit is connected to TV or Projector supporting Auto Lipsync Correction in HDMI 1.3a. For instructions on Auto Lipsync Correction, see page 38.
DUAL BACKUP MEMORY
The unit stores settings information in nonvolatile memory even when the main power supply is turned off. Using the Dual Backup Memory function, you can write settings information to another memory area to back up saved settings for recovery anytime as needed.
BACKUP
Set up the unit in the state for which you want to store the settings. Hold the MEMORY and ENTER buttons on the front panel simultaneously for at least 3 seconds.
“MEMORY SAVING” is displayed and the unit’s settings are saved. The stored settings information is retained until Dual Backup Memory is used again and the information is overwritten.
M E M O R Y S A V I N G
Note:
•The following settings values cannot be backed up.
•Main ZONE Volume
•ZONE A Volume
•ZONE Speaker A Volume
|
| ENGLISH |
|
| |
RECOVERY OF MEMORY |
| NAMESAND | FUNCTION | ||
Recover backed up settings as follows. | |||||
|
| ||||
Hold the MEMORY and MENU buttons on the front |
|
| |||
panel simultaneously for at least 3 seconds. |
|
| |||
|
|
| BASIC | CONNECTIONS | |
“MEMORY LOAD” is displayed and the unit’s stored | OPERATION | ||||
|
| ||||
settings are reapplied. |
|
|
| ||
The unit temporarily enters standby mode. If there is | BASIC | ||||
no backup data, “NO BACKUP” is displayed and no | |||||
|
| ||||
data is recovered. |
|
|
| ||
M E M O R Y | L O A D | ADVANCED | CONNECTIONS | ||
Note: | B A C K U P | ||||
N O |
|
| |||
• Because the following settings values are |
|
| |||
not backed up, each Volume value is set to |
|
| |||
Minimum. |
|
| SETUP | ||
• Main ZONE Volume |
| ||||
|
|
| |||
• ZONE A Volume |
|
|
| ||
• ZONE Speaker A Volume |
|
| |||
|
|
| ADVANCED | OPERATION | |
|
|
| TROUBLESHOOTING | ||
|
|
| OTHERS | ||
45
