
ENGLISH
NAMESAND FUNCTION | CLEARING STORED PRESET STATIONS | |
You can remove preset stations from the memory | ||
| ||
| using the following procedure. |
|
| 2. | 3. | |
|
|
| 2. | |
BASIC CONNECTIONS |
|
| 3. | |
BASIC |
|
| ||
1. Recall the preset number to be cleared with | ||||
OPERATION | ||||
2. | Press the MEMORY button on the front panel | |||
|
| the method described in “Recalling” a preset | ||
|
| station. |
| |
ADVANCED CONNECTIONS |
| or press the MEMO button on the remote | ||
| remote controller. | |||
|
| controller. | ||
| 3. The stored preset number blinks in the display | |||
|
| for 5 seconds. While blinking, press the CLEAR | ||
|
| button on the front panel or the CL button on the | ||
| 4. “xx CLEAR” appears on the display to indicate | |||
|
| that the specified preset number has been | ||
SETUP |
| cleared. |
| |
Note: |
| |||
|
| |||
|
| • To clear all stored preset stations, press and hold the | ||
|
| |||
ADVANCED OPERATION |
|
|
| |
TROUBLESHOOTING |
|
|
| |
OTHERS |
|
|
|
SORTING PRESET STATIONS
If you have stations memorized, and there is a gap in the sequential order:
I.e. the stations are stored as follows
1)87.1 MHz
2)93.1 MHz
3)94.7 MHz
10)105.9 MHz
(notice there is no stations programmed for presets for
“PRESET SORT” will appear on the display and sorting will be done.
NAME INPUT OF THE PRESET STATION.
This function allows the name of each preset channel to be entered using alphanumeric characters. Before name inputting, you need to store preset stations with the preset memory operation.
4.5. 2. 5. 6.
4. 5.
2.
5. 6.
1. Recall the preset number to be inputted name with the method described in “Recalling” a preset station.
2. Press the MEMORY button on the front panel or press the MEMO button on the remote controller for more than 3 seconds.
3. The left most column of the station name indicator fl ashes, indicating the character entry ready status.
4. When you press the 3 or 4 cursor buttons on the front panel or the remote controller, alphabetic and numeric characters will be displayed in the following order:
A ↔ B ↔ C ... Z ↔ 1 ↔ 2 ↔ 3 ..... 0 ↔ – ↔ +
↔/ ↔ (Blank) ↔ A UP →
←DOWN
5. After selecting the first character to be entered, press the MEMORY or ENTER button, or press the MEMO button on the remote controller.
The entry in this column is fi xed and the next column starts to fl ash. Fill the next column the same way.
To move back and forth between the characters, press the 1 / 2 cursor buttons.
Note:
•Unused columns should be filled by entering blanks.
6.To save the name, press the MEMORY or ENTER button on the front panel, or press the MEMO button on the remote controller for more than 2 seconds.
Instead of using the 3 and 4 cursor buttons to select characters, characters can be input from the numeric keys of the remote controller. See the below table for a correspondence between characters and numeric keys.
Ten keypad | Press, press again, press again, etc. |
1 | A → B → C → 1 → A |
2 | D → E → F → 2 → D |
3 | G → H → I → 3 → G |
4 | J → K → L → 4 → J |
5 | M → N → O → 5 → M |
6 | P → Q → R → 6 → P |
7 | S → T → U → 7 → S |
8 | V → W → X → 8 → V |
9 | Y → Z → space → 9 → Y |
0 | – → + → / → 0 → – |
52