| Contents | Connections | Playback | Settings | Tips | Appendix | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Symptom |
|
|
| Cause / Solution |
|
| Page |
| DTS Neo:X mode cannot | 0 | It cannot be selected when “Speaker Config.” - “Surround” is set for “None”. |
|
| 236 | ||
| be selected. |
|
|
|
|
| ||
| 0 | DTS Neo:X cannot be selected when using the headphones. |
|
| - | |||
| Dolby Surround mode | 0 | Dolby Surround cannot be selected when using the headphones. |
|
| - | ||
| cannot be selected. |
|
|
|
|
|
|
|
| Audyssey MultEQ® XT32, | 0 | These cannot be selected when you have not performed Audyssey® Setup. |
|
| 210 | ||
| Audyssey Dynamic EQ®, |
|
|
|
|
| ||
| 0 | Switch to a sound mode other than “Direct” or “Pure Direct”. |
|
| 144 | |||
| Audyssey Dynamic |
|
|
|
|
|
|
|
| 0 | These cannot be selected when using the headphones. |
|
| - | |||
| Volume® and Audyssey |
|
| |||||
| LFC™ cannot be selected. |
|
|
|
|
|
|
|
| Audyssey DSX® cannot be | 0 | It can be selected when using the front height or front wide speakers. |
|
| 237 | ||
| selected. |
|
|
|
|
| ||
| 0 | It can be selected when using the center speaker. |
|
| 236 | |||
|
| 0 | Switch the sound mode to Dolby sound mode or DTS sound mode. |
|
| 143 | ||
|
| 0 | This cannot be selected when using the headphones. |
|
| - | ||
|
| 0 | This cannot be set when the input signal is a |
|
| - | ||
| 0 | Check that an analog signal or PCM signal (Sample Rate = 44.1/48 kHz) is input. For playback of |
| 185 | ||||
| selected. |
| multichannel signals such as Dolby Digital or DTS surround, |
|
| |||
|
| 0 | Switch to a sound mode other than “Direct” or “Pure Direct”. |
|
| 144 | ||
| No audio is output from | 0 | In ZONE2/ZONE3, the audio can be played back when signals input from digital connectors (OPTICAL/ | - | ||||
| PRE OUT or speakers for |
| COAXIAL) are in 2ch PCM format. |
|
|
|
| |
| ZONE2/ZONE3. |
|
|
|
| |||
| 0 | In ZONE2, the audio can be played back when signals input from the HDMI connector are in 2ch PCM |
| 256 | ||||
|
|
| format. To play back the audio in ZONE2 irrespective of the input signal format, set “HDMI Audio” in the |
| ||||
|
|
| menu to “PCM”. Depending on the played back device, the audio may not be played back even with this |
| ||||
|
|
| setting. In that case, set the audio format to “PCM (2ch)” on the played back device. |
|
| |||
|
| 0 | When listening to audio from a Bluetooth device in ZONE2/ZONE3, remove any obstructions between the | - | ||||
|
|
| Bluetooth device and this unit and use it within a range of about 32.8 ft/10 m. |
|
|
|
Front panel | Display | Rear panel | 286 | Remote | Index |