Maxon Telecom SP200, SP210 - page 12

Maxon SP200/210 Radio SP200/210

SPECIFICATIONS DRAFT Issue 1.0

Page 2-2 03/01

Environmental

Operating Temperature Range -15 to +35°C (nom inal)

-20 to +55°C (extreme),

Storage Temperature Range -40 to +80°C (storage)

Charging Temperature Range 0 to +30°C

Humidity EIA/TIA 603 (95%)

Protection against ingress of IEC 529 IP54

dust and water

Vibration BS2011 : Part 2.1Fc IEC 68-2-6

Part 2.1Fd IEC 68-2-34

Robustness Mil Std 810 C Procedures I, II & V

ESD 20kV (C-MIC >= 15kV)

EMC EMC Directive 89/336/EEC May 89

Physical Dimensions 112 x 61 x 40mm

(Excluding antenna and with QPA1350 pack)

Synthesiser

Reference Crystal

Frequency: 12.8MHz

Holder: HC-18

Accuracy: ± 3ppm over –30 to +60°C

Ageing Rate: < 2ppm / Year in the first year

< 1ppm / Year in subsequent years

Synthesiser Lock Time: < 10mS

Switching Times

Tx to Rx, same frequency < 20mS

Rx to Tx, same frequency < 20mS

Rx to Rx < 20mS

(over switching bandwidth)

Rx to Tx / Tx to Rx < 20mS

(over switching bandwidth)

Receiver Sensitivity <-118dBm (VHF), <-117dBm (UHF)

Squelch Sensitivity 7 – 12dB SINAD

Adjacent Channel Selectivity Better than 70dB

Sub Audio Tones – CTCSS / DCS

Decode Sensitivity Method (decrease signal level @ 10% peak devia tion)

All tones <=9dB SINAD

CTCSS Tone Range 67 – 250Hz @ 0.3% accuracy

50 – 260Hz @ 0.3% accuracy (non-standard tones)

DCS Tone Standard Standard & Inver ted

Programmer SMP 6100

Contents

Main Page Page Page TABLE OF CONTENTS 1 INTRODUCTION 1-1 2 SPECIFICATIONS 2-1 3 ACCESSORIES & OPTIONS 3-1 4 INSTALLATION, COMMISSIONING & ALIGNMENT 4-1 8 EXPLODED MECHANICAL DRAWINGS & PARTS LISTS 8-1 9 CIRCUIT DIAGRAMS & PCB LAYOUTS 9-1 10 SPARE PARTS 10-1 11 APPENDIX ACC-2003 ALIGNMENT BOX 11-1 LIST OF FIGURES LIST OF TABLES Page 1 INTRODUCTION 1.1 Using this Manual 1.2 Amendments to this Manual 1.3 Contact Information 2 SPECIFICATIONS 2.1 General Page 3 ACCESSORIES & OPTIONS 3.1 Pre-Install Check 3.2 Accessories 3.3 Options Page 4 INSTALLATION, COMMISSIONING & ALIGNMENT 4.1 Installation 11 12 4.2 Connections 4.3 Commissioning Page Page Page 4.3.1 Test Equipment Connection 4.3.2 Transmitter Performance Tests 4.3.3 Receiver Performance Tests 4.4 Power Adjustment PowerSquelch 4.5 Alignment 4.5.1 Preparation 4.5.2 Disassembly and Re-assembly of the Radio RF PCB 4.5.3 PLL Alignment 4.5.4 Squelch Sensitivity 4.5.5 Transmitter Alignment RADIOCOMMUNICATIONS TEST SET Page 4.5.6 Receiver Alignment 5 DETAILED FUNCTIONAL DESCRIPTION 5.1 Introduction 5.2 Common Circuits 5.3 Audio ASIC 5.3.1 Audio Signal Path 5.3.2 Sat Signal Path 5.3.3 Miscellaneous Signals and Controller 5.4 Audio/SAT Circuits 5.5 Common RF Circuits ~ Page 5.6 Transmitter 5.7 Receiver ~ Page Page 6 TROUBLESHOOTING 6.1 Diagnostic Function 6.2 Troubleshooting Chart 6.3 Voltage Charts 6.3.1 Transistors (Main Circuit) Maxon SP200/210 Radio SP200/210 TROUBLESHOOTING Issue 1.0 Page 6-4 03/01 6.3.2 Integrated Circuits Table 6-5 - Integrated Circuit Voltages (Transmit) Receive Table 6-4 - Integrated Circuit Voltages (Receive) Transmit Page Page Page Page 7 PROGRAMMING 7.1 SMP6100 7.1.1 Introduction 7.1.2 Getting Started 7.1.3 Programming Page Page Page 8 EXPLODED MECHANICAL DRAWINGS & PARTS LISTS 8.1 Parts List 8.2 Spare Parts Page Page Page Page Page Page 8.4 SL100 VHF Parts List 8.4.1 V2 Control Circuit Page 8.4.2 V2 RF Page Page 8.4.3 TCXO Assembly 8.4.4 V2 VCO 8.4.5 V2 Front End 8.5 SL100 UHF Parts List 8.5.1 U2 Contr o l Circuit Page 8.5.2 U2 RF Page Page 8.5.3 TCXO 8.5.4 VCO Page 9 CIRCUIT DIAGRAMS & PCB LAYOUTS Page Page Page Page Page Page Page 10 SPARE PARTS 10.1 Spare Parts 10.1.1 Component Replacement Page Page 11 APPENDIX ACC-2003 ALIGNMENT BOX 11.1 Purpose 11.2 Test Equipment 11.3 Calibration Program 11.3.1 Operation Page Page 11.3.2 Adjustment of ASIC values Page 11.3.3 Transmit Adjustments 11.3.4 Receive Adjustments 11.4 Default Settings 11.4.1 V1 Band Default Settings 11.4.2 V2 Band Default Settings 11.4.3 U1 Band Default Settings 11.4.4 U2 Band Default Settings