Receiver Alignment, Audio Volume Level | Maxon Telecom SP210, SP200

Maxon SP200/210 Radio

SP200/210

This completes the transmitter alignment process.

4.5.6 Receiver Alignment

Audio Volume Level

a.Set the test set to the appropriate frequency at –47dBm with 1kHz tone modulation at 60% system deviation:

12.5kHz channel spacing 1.5kHz dev. or 20kHz channel spacing2.4kHz dev. or 25kHz channel spacing3kHz dev.

b.Select Channel 1.

c.With the calibration program running on the PC, select Rx_Vol.

d.Turn the volume control to maximum.

e.Using the PageUp and PageDown keys, press until the desired maximum volume level is achieved.

Note: -17.5dB corresponds to 2.10V (+/-0.2V) into 4 ohm speaker.

At maximum volume, nominal distortion is 10%.

f.Write the changes to the radio.

It may be necessary to carry out adjustment of the squelch setting, see Section 4.5.4.

This completes the receiver alignment process.

The following parameters would NOT normally be adjusted unless specific environmental conditions necessitate a change:

INTRIM on the receiver (Audio from IF IC.)

SATRIM on the receiver (gain received – sub audible tone)

Refer to the ACC-2003 User Guide for details.

INSTALLATION, COMMISSIONING & ALIGNMENT -	Issue 1.0
Page 4-14	03/01

Image 28

Maxon Telecom SP210, SP200 Receiver Alignment, Audio Volume Level, At maximum volume, nominal distortion is 10%

Contents

SP200/210 NSW Australia Tel +61 0 2 9707 Amendment Record Sheet Issue No Effective Date Reason for Change SignatureAmendment Record Sheet Maxon SP200/210 Radio Table of Contents SL100 UHF Parts List 11.4 Default Settings 11-810-1 11-1 List of Tables Maxon SP200/210 Radio Issue 03/01 Using this Manual IntroductionAmendments to this Manual Category C Engineering Bulletin Contact Information Specifications General Environmental Operating Temperature Range Physical Dimensions SynthesiserVibration ESD EMC Pre-Install Check Accessories Accessories & OptionsOptions Accessories & Options INSTALLATION, Commissioning & Alignment InstallationINSTALLATION, Commissioning & Alignment Connections Commissioning Recommended Test Equipment Commissioning Equipment Commissioning Kit Test Equipment Set-up using Discrete Test Equipment Discrete Test Equipment SK 3100 Service Kit Transmitter Performance Tests Test Equipment ConnectionReceiver Performance Tests Squelch Power AdjustmentAudio Output Tests without Disassembly AlignmentPreparation VHF Removing and Replacing Battery Disassembly and Re-assembly of the RadioRemoving and Replacing the Belt Clip Location of Adjustment Points Removing and Replacing the Main AssemblyPLL Alignment Transmitter Alignment Squelch SensitivityTcxo Radiocommunications Test SET Audio deviation adjustment Balance AdjustmentCtcss / DCS deviation At maximum volume, nominal distortion is 10% Audio Volume LevelReceiver Alignment Detailed Functional Description IntroductionCommon Circuits Eeprom Audio Signal Path Audio Asic Sat Signal Path Miscellaneous Signals and Controller Audio/SAT Circuits Battery Low Indicator Circuit LEDs and indicatorsCommon RF Circuits PLL Synthesiser PLL IC Out-of-Lock DetectorCharge Pump and Loop Filter DC to DC Converter Antenna Switch Automatic power control APC circuitsTransmitter PA module Receiver Front End First Mixer Second mixer, Second IF, FM detectorSquelch Mute Circuit 16kHz Band Pass Filter AF Output Low Pass Filter Noise detector circuitSpeaker Audio Amplifier Troubleshooting Diagnostic FunctionDiagnostics Troubleshooting Troubleshooting Chart If IC Transistors Main Circuit Voltage ChartsMain Circuit Transistor Voltages Integrated Circuit Voltages Receive Integrated CircuitsIntegrated Circuit Voltages Transmit Troubleshooting Troubleshooting Troubleshooting Troubleshooting Programming SMP6100Introduction Getting Started Select Features Menu ScanningProgram/Print/Save Program Radio Print Data Save Data to Disk Maxon SP200/200 Radio SP200/210 Exploded Mechanical Drawings & Parts Lists Parts ListExploded Mechanical Drawings & Parts Lists Spare Parts SL100U2 SL100V2 Mechanical Parts For details on servicing, please refer to Section Parts List for Exploded Mechanical Drawing LCD TTR 1866 Dpfdpw PCB LCD SKPT-110VASML-020MLTT86 SMD NUT M7 Bsbm PCB VCO PCB RF Aldc Bsbm M2.6 V2 Control Circuit SL100 VHF Parts List05B-000-5Z Diode Switching KDS181S A3 Chip Ceramic 0.001UF GRM39 X7R102K 50V PChip Ceramic 0.012UF GRM39 X7R123K 25V P Chip Ceramic 0.0022UF GRM39 X7R222J 50V P 2 V2 RF SW Tact SKPT-1101VA RES.CHIP Trimmer 1K RH03E1C13X RES.CHIP Trimmer 10K RH03E1C14XThermistor Chip 33KNTCCS32163SH333KC TH1 Elect Capacitor 10UF 16V 20% RE Power Module GNOK-M68776-E01 IC9 Chip Ceramic 39PF GRM40 COG390J 50V PChip Ceramic 43PF GRM40 COG430J 50V P Chip Ceramic 47PF GRM39 COG470J 50V P Tcxo Assembly 4 V2 VCO 5 V2 Front End SL100 UHF Parts List U2 Control Circuit Connector Waffer 2 U2 RF Chip Resistor 12KChip Resistor 18K Chip Resistor 39K RES.CHIP Trimmer K RH03E1C13X Chip Ceramic 0.0015UF GRM39 X7R152K 50V PChip Ceramic 10PF GRM40 COG100C 50V P Chip Ceramic Power Mpduleuhf M68732HGNOK IC9 Chip Ceramic 2.2PF GRM40 COG2R2C 50V PChip Ceramic 470PF GRM40 COG471J 50V P Chip Ceramic 4.7PF GRM40 COG4R7C 50V P Tcxo Coil Chip 18NHLL2012-F18NMCoil Spring X0.35X7TR Coil Spring 2X0.75X3TL SMD 4 VCO Maxon SP200/210 Radio Circuit Diagrams & PCB Layouts Circuit Diagrams & PCB LayoutsRF PCB Tcxo Circuit Diagrams & PCB Layouts Digital Board Layout Top Side Digital Board Layout Bottom Side RF Board Layout Top Side Issue RF Board Layout Bottom Side P406787a Front End Front-End Board Layout Tcxo Board Layout 10SPARE Parts Spare Parts & Maintenance Policy10.1Spare Parts Component Replacement Surface mount component replacementSurface mount components Surface mount removal Surface mounted integrated circuit replacement Spare Parts & Maintenance Policy 11APPENDIX ACC-2003 Alignment BOX 11.1Purpose11.2Test Equipment 11.3Calibration Program Calibration Program Primary Screen Appendix a ACC-2003 Alignment BOX Asic Control Screen Rx TXTRIM2 Adjustment of Asic valuesTXTRIM3 RX VOL SAT Balance Transmit AdjustmentsSAT Deviation Receive Adjustments Audio Output Level 11.4Default Settings 11.4.1 V1 Band Default SettingsV1 Default Frequency Table V1 Default Asic Settings V2 Default Frequency Table 11.4.2 V2 Band Default SettingsV2 Default Asic Settings U1 Default Frequency Table 11.4.3 U1 Band Default SettingsU1 Default Asic Settings U2 Default Frequency Table 11.4.4 U2 Band Default SettingsU2 Default Asic Settings