IrDA Connector, Connecting the USB Ports | Microsoft G7VP2 guide

Hardware Installation

Connecting the USB Ports

As an option, one card-edge bracket mounted with two USB port cables may be provided with the system board. The ends of the cables are attached to a connector. Connect the USB cable connector to J2 and J3 on the system board. The USB port cables can be inserted only if pin 1 of the cable (red wire) is aligned with pin 1 of J2 and J3. Pin 5 of J3 has been removed and the hole in the USB cable connector, which corresponds to pin 5, has been plugged to prevent incorrectly inserting the connector. Mount the card-edge bracket to the system chassis.

2.9.8 IrDA Connector

The system board is equipped with an IrDA connector for wireless connectivity between your computer and peripheral devices. Connect your IrDA cable to connector J6 on the system board. Make sure “Onboard UART 2 Mode” in the Integrated Peripherals setup of the Award BIOS is set to the type of IrDA standard supported by your IrDA peripheral/device.

You must have the proper drivers installed in your operating system to use this connector. Refer to your operating system’s manual or documentation.

Pin Function

1 IRTX

2Ground

3IRRX

4 IRR3

5Vcc

2

29

Image 29

Microsoft G7VP2 manual IrDA Connector, Connecting the USB Ports

Contents

37310911 G7VP2 Trademarks Copyright FCC and DOC Statement on Class B Table of Contents Appendix C Troubleshooting Appendix B System Error MessageSupported Softwares Appendix a Identifying Processors Features Features and SpecificationsIntroduction Introduction Level 2 Cache Memory ConnectorsExpansion Slots Desktop Management Interface DMI Intelligence RTC Timer to Power-on the System ATX power supply only Dual Function Power Button ATX power supply onlyWatchdog Timer Virus Protection Package Checklist System Board Layout Hardware InstallationHardware Installation Example on the right Switch Off DIP Switch Settings for Cyrix Processors DIP Switch Settings for Intel Processors DIP Switch Settings for IDT Processors DIP Switch Settings for IBM Processors DIP Switch Settings for AMD Processors External System Bus Clock Settings Frequency Ratio Settings for IDT Processors DIP Switch and Jumper Settings for Core Voltage Jumper JP1 Clear Cmos Data Jumper Settings for Clearing Cmos Data Jumper JP2 Power Supply Type Jumper Settings for Power Supply Type Pins 1 and 2 On ATX Power Jumper JPP ATX Power-On/Off Select Jumper JP4 Sdram Clock Jumper Settings for Sdram Clock Dimm Jumper JP10 Watchdog Timer Jumper Settings for Watchdog Timer Serial Ports Connecting the Serial Ports Hardware Installation Keyboard Port/Connector Parallel Port Hardware Installation 3 PS/2 Mouse PortConnecting the Parallel Printer Port IDE Hard Disk Interface Hardware Installation Floppy Disk Drive Controller Adding a Second IDE Hard Drive Universal Serial Bus Ports Connecting the USB Ports IrDA Connector Chassis Fan Connector Hardware Installation CPU Fan Connector Hardware Installation 11 J13 LEDs and Switches Keylock Keylock and Power LED Connector Hardware Installation Power Supply Connectors Award Bios Setup Utility Award Bios Setup UtilityStandard Cmos Setup Basic Input/Output System Time Date Halt On Drive a and Drive BVideo Memory Virus Warning Award Bios Setup Utility Bios Features Setup Boot Sequence Quick Power On Self TestBoot Up Floppy Seek Boot Up NumLock Status Typematic Delay Msec Typematic Rate SettingMemory ECC Function Typematic Rate Chars/Sec OS Select for Dram 64MB Video Bios ShadowHDD S.M.A.R.T. Capability C8000-CBFFF Shadow to DC000-DFFFF Shadow Software Power-off Award Bios Setup Utility Chipset Features Setup CPU Fan Speed Limit and Chassis Fan Speed Limit CPU Temperature LimitSystem Health Monitor +3.3V, +5V and +12V Voltages Power Management Setup PM Control by APM Power ManagementVideo Off Method Video Off After Suspend Mode Standby ModeHDD Power Down Soft-Off by Pwrbtn Timer hhmmss Resume On AlarmDate of Month PM Events Resources Controlled By Award Bios Setup Utility 5 PNP/PCI ConfigurationReset Configuration Data PCI Slot 1 Use IRQ and PCI Slot 2 Use IRQ PCI IRQ Actived ByAssign IRQ for VGA Integrated Peripherals Award Bios Setup Utility Load Fail-Safe SettingsLoad Optimal Settings Onboard Primary PCI IDE and Onboard Secondary PCI IDE IDE Prefetch ModeIDE HDD Block Mode USB Controller Onboard Uart 2 ModeUSB Keyboard Support Onboard FDC Controller Onboard Parallel Port IR Duplex ModeUse IR Pins User Password Award Bios Setup Utility Supervisor Password Award Bios Setup Utility IDE HDD Auto Detection Exit Without Saving Award Bios Setup Utility Save & Exit Setup Desktop Management Interface DMI Supported SoftwaresSupported Softwares Running the DMI Utility Edit DMI Supported Softwares Using the DMI Utility Save DMI File Supported Softwares Add DMILoad DMI File Genesys Logic System Health Monitor for VIA System Health Monitor Utility Drivers Installing the Utility Intel Processors Appendix a Identifying ProcessorsCyrix Processors Identifying Processors AMD Processors IBM Processor C6-PSME200GA IDT Processors Post Beep Appendix B System Error MessageError Messages System Error Message Troubleshooting Checklist Appendix C -TroubleshootingTroubleshooting C Monitor/Display Floppy Drive TroubleshootingPower Supply Hard disk failure Troubleshooting Hard Drive System Board Troubleshooting Serial PortKeyboard