Front Panel of UNO-3074 | Microsoft specification

Chapter 2 Hardware Functionality

2.1 Introduction

The two figures below show the connectors on UNO-3074, and following sections give you detailed information about function of each peripheral.

Figure 2.1: Front Panel of UNO-3074

UNO-3074 User Manual

12

Image 22

Microsoft user manual Front Panel of UNO-3074

Contents

UNO-3074 Acknowledgements CopyrightSupport Product Warranty 2 years Declaration of Conformity FCC Class a Technical Support and Assistance Safety Instructions Safety Precaution Static Electricity Contents Chapter Initial Setup Appendix Programming the Watchdog Timer Page Overview Introduction Open Architecture Designed for Automation Off-the-shelf Universal PCI Extensions Front Access ConnectionsAn Industry-Proven Design Designed to Fit Into Control Cabinets Flexible Networking Options Onboard DI/O for Counter, Alarm/Event HandlingPopular Operating Systems and Rapid Application Development CPU Hardware SpecificationsBattery Backup RAM 512 KB Chipset RS-232 Speed Ch Isolated Digital Output DO0~DO3 Two 16-bit Counters/TimersCh Isolated Digital Input DI0~DI3 Anti-Shock Power Consumption 24 W Typical Safety PrecautionsPower Supply 16 ~ 36 VDC Chassis Size WxHxD Chassis Dimensions Chassis Dimensions for CeleronM 1GHz Chassis for Pentium 1.8GHz or Faster CPU Accessories Packing List Hardware Functionality Front Panel of UNO-3074 1 16C550 UARTs with 16-byte Fifo Standard RS-232 Interface COM1~COM2RS-232/422/485 Interface COM3~COM4 2 RS-422/485 Detection 4 RS-232/422/485 Selection 5 RS-485 Auto Flow/RS-422 Master/Slave Selection Auto Flow & RS-422 Slave/Masters 6 IRQ, I/O Address and Transmission Rate SettingVector address for share IRQ 1D0H IRQ Setting via Switch 1 at SW3 Transmission Rate Switch 2 at SW3 Termination Resistor JP6 LAN Ethernet ConnectorOnboard Isolated Digital Input Pin Assignments Digital Input Connector Signal Description Isolated Inputs Interrupt Control Register Interrupt Function of the DI SignalsIRQ Level Interrupt Control Register Bit Map Interrupt Triggering Edge Control Interrupt Enable Control FunctionInterrupt Flag Bit Digital Output Connector Signals Onboard Isolated Digital Output 10 Digital Output Power On Configuration Power On ConfigurationIsolated Outputs Isolated Digital Output Connection Counter/Timer Control Register Onboard Isolated Counter/Timer11 Counter/Timer Control Register Bit Map Counter 0 Function Block Counter 1 Function Block Counter Internal Clock 4 32-bit Counter Function Block CTR32Set=1Counter Clock Source Counter Gate Source 14 Counter Gate Source Control Bit Counter Output DestinationCounter Interrupt Flag 15 Counter Output Destination Control Bit Cascaded 32-bit Counter Power Input17 32-bit Counter Control Bit 12 LED Locations to Monitor Power Input 18 Power Register Bit Map LED and Buzzer for System Diagnosis 19 LED & Buzzer Control Register 20 Programmable LED Control Bit Pcmcia PC Card Slot USB ConnectorPS/2 Keyboard and Mouse Connector 21 Programmable Buzzer Control BitPage Make sure the IRQ of Pcmcia device is VGA Display Connector Page Battery Backup Sram 14 LED Location for Battery Backup Lithium Battery Specification Reset ButtonOutput voltage 3 VDC Initial Setup JP2 on mainboard refer to Figures A.3 Connecting PowerInserting a CompactFlash Card JP1 on daughterboard refer to Figure A.4 Installing a Hard Disk Correct way is shown by the first figure belowPage Page Page IDE Connector CN1 and CN2 Installing a PCI-bus Card 1st Anti-Vibration Rubber 2nd PCI-bus Card Installation Installing Power Cable Mounting UNO-3074 UNO-3074 Improper Installation UNO-3074 Mounting Caution UNO-3074 Correct Installation Bios Setup and System Assignments Page System Settings and Pin Assignments System I/O Address and Interrupt Assignments Table A.1 UNO-3074 System I/O Port Table A.2 UNO-3074 Interrupt Assignments Interrupt No Interrupt Source Board Connectors and Jumpers Figure A.1 Backplane Connector & Jumpers Figure A.3 Mainboard Connector & Jumpers Front Figure A.4 Daughter Connector & Jumpers Front Figure A.5 Daughter Connector & Jumpers Back Table A.3 Connector and Jumper Descriptions Table A.4 Connector and Jumper Descriptions Table A.5 Connector & Jumper Descriptions SW1 UNO-3074 Control Register Table A.6 UNO-3074 Control Register RS-232 Standard Serial Port COM1~COM2 Table A.7 RS-232 Serial Port Pin Assigns RS-232/422/485 Serial Port COM3~COM4 Ethernet RJ-45 Connector LAN1~LAN2Table A.9 Ethernet RJ-45 Connector Pin Assigns Table A.8 RS-232/422/485 Serial Port Pin Assigns Power Screw Terminal PWR Table A.10 Power Connector Pin Assignments Table A.11 Keyboard & Mouse Connector Pins PS/2 Keyboard and Mouse ConnectorUSB Connector USB1~USB4 Table A.12 USB Connector Pin Assignments Table A.13 VGA Adaptor Cable Pin Assignmen Page Programming the Watchdog Timer Appendix B Programming the Watchdog Timer