Reset Button, Lithium Battery Specification | Microsoft UNO-3074

2.13.1 Lithium Battery Specification

Type: BR2032 (Using CR2032 is NOT recommended)

Output voltage: 3 VDC

Location: Mainboard of UNO-3074. (Figure 2.15)

When the voltage of battery < 2.5 VDC, BTRY LED will light up.

Figure 2.15: Lithium Battery for SRAM

2.14 Reset Button

Press the "Reset" button to activate the reset function. (SW1 of daughterboard)

Note:

Please refer to Figure A.5 for location of SW1.

UNO-3074 User Manual

38

Image 48

Microsoft UNO-3074 user manual Reset Button, Lithium Battery Specification, Output voltage 3 VDC

Contents

UNO-3074 Copyright AcknowledgementsSupport Product Warranty 2 years Declaration of Conformity FCC Class a Technical Support and Assistance Safety Instructions Safety Precaution Static Electricity Contents Chapter Initial Setup Appendix Programming the Watchdog Timer Page Overview Introduction Open Architecture Designed for Automation Front Access Connections An Industry-Proven DesignOff-the-shelf Universal PCI Extensions Designed to Fit Into Control Cabinets Onboard DI/O for Counter, Alarm/Event Handling Flexible Networking OptionsPopular Operating Systems and Rapid Application Development Hardware Specifications Battery Backup RAM 512 KB ChipsetCPU RS-232 Speed Two 16-bit Counters/Timers Ch Isolated Digital Input DI0~DI3Ch Isolated Digital Output DO0~DO3 Anti-Shock Safety Precautions Power Supply 16 ~ 36 VDCPower Consumption 24 W Typical Chassis Size WxHxD Chassis Dimensions Chassis Dimensions for CeleronM 1GHz Chassis for Pentium 1.8GHz or Faster CPU Accessories Packing List Hardware Functionality Front Panel of UNO-3074 RS-232 Interface COM1~COM2 RS-232/422/485 Interface COM3~COM41 16C550 UARTs with 16-byte Fifo Standard 2 RS-422/485 Detection 4 RS-232/422/485 Selection 5 RS-485 Auto Flow/RS-422 Master/Slave Selection 6 IRQ, I/O Address and Transmission Rate Setting Auto Flow & RS-422 Slave/MastersVector address for share IRQ 1D0H IRQ Setting via Switch 1 at SW3 Transmission Rate Switch 2 at SW3 LAN Ethernet Connector Onboard Isolated Digital InputTermination Resistor JP6 Pin Assignments Digital Input Connector Signal Description Isolated Inputs Interrupt Function of the DI Signals IRQ LevelInterrupt Control Register Interrupt Control Register Bit Map Interrupt Enable Control Function Interrupt Triggering Edge ControlInterrupt Flag Bit Digital Output Connector Signals Onboard Isolated Digital Output Power On Configuration 10 Digital Output Power On ConfigurationIsolated Outputs Isolated Digital Output Connection Onboard Isolated Counter/Timer Counter/Timer Control Register11 Counter/Timer Control Register Bit Map Counter 0 Function Block Counter 1 Function Block 4 32-bit Counter Function Block CTR32Set=1 Counter Clock SourceCounter Internal Clock Counter Gate Source Counter Output Destination Counter Interrupt Flag14 Counter Gate Source Control Bit 15 Counter Output Destination Control Bit Power Input Cascaded 32-bit Counter17 32-bit Counter Control Bit 12 LED Locations to Monitor Power Input 18 Power Register Bit Map LED and Buzzer for System Diagnosis 19 LED & Buzzer Control Register 20 Programmable LED Control Bit USB Connector PS/2 Keyboard and Mouse ConnectorPcmcia PC Card Slot 21 Programmable Buzzer Control BitPage Make sure the IRQ of Pcmcia device is VGA Display Connector Page Battery Backup Sram 14 LED Location for Battery Backup Reset Button Lithium Battery SpecificationOutput voltage 3 VDC Initial Setup Connecting Power Inserting a CompactFlash CardJP2 on mainboard refer to Figures A.3 JP1 on daughterboard refer to Figure A.4 Installing a Hard Disk Correct way is shown by the first figure belowPage Page Page IDE Connector CN1 and CN2 Installing a PCI-bus Card 1st Anti-Vibration Rubber 2nd PCI-bus Card Installation Installing Power Cable Mounting UNO-3074 UNO-3074 Improper Installation UNO-3074 Mounting Caution UNO-3074 Correct Installation Bios Setup and System Assignments Page System Settings and Pin Assignments System I/O Address and Interrupt Assignments Table A.1 UNO-3074 System I/O Port Table A.2 UNO-3074 Interrupt Assignments Interrupt No Interrupt Source Board Connectors and Jumpers Figure A.1 Backplane Connector & Jumpers Figure A.3 Mainboard Connector & Jumpers Front Figure A.4 Daughter Connector & Jumpers Front Figure A.5 Daughter Connector & Jumpers Back Table A.3 Connector and Jumper Descriptions Table A.4 Connector and Jumper Descriptions Table A.5 Connector & Jumper Descriptions SW1 UNO-3074 Control Register Table A.6 UNO-3074 Control Register RS-232 Standard Serial Port COM1~COM2 Table A.7 RS-232 Serial Port Pin Assigns Ethernet RJ-45 Connector LAN1~LAN2 Table A.9 Ethernet RJ-45 Connector Pin AssignsRS-232/422/485 Serial Port COM3~COM4 Table A.8 RS-232/422/485 Serial Port Pin Assigns Power Screw Terminal PWR Table A.10 Power Connector Pin Assignments PS/2 Keyboard and Mouse Connector USB Connector USB1~USB4Table A.11 Keyboard & Mouse Connector Pins Table A.12 USB Connector Pin Assignments Table A.13 VGA Adaptor Cable Pin Assignmen Page Programming the Watchdog Timer Appendix B Programming the Watchdog Timer