Blowing Out Inside Of Unit | Miller Electric ProHeat 35 specs

9-8. Blowing Out Inside Of Unit

! Turn Off welding power source and disconnect input power.

! Remove wrapper and be sure input capacitors are discharged.

Blow out inside of unit. Blow out fan motors in right side panel and front panel.

804 625-B

Notes

MATERIAL THICKNESS REFERENCE CHART

24 Gauge (.025 in)

22 Gauge (.031 in)

20 Gauge (.037 in)

18 Gauge (.050 in)

16 Gauge (.063 in)

14 Gauge (.078 in) 1/8 in (.125 in)

3/16 in (.188 in)

1/4 in (.25 in)

5/16 in (.313 in)

3/8 in (.375 in)

1/2 in (.5 in)

OM-222 166 Page 47

Page 53

Image 53

Miller Electric ProHeat 35 manual Blowing Out Inside Of Unit, Material Thickness Reference Chart

Contents

File Induction Heating OM-222 166K 2007−11 ProcessesDescription From Miller to You Table of Contents Routine Maintenance Blowing Out Inside Of Unit − MaintenanceLimit Conditions Limit Condition Codes Fault Conditions EMF Information Decstat1/07 DirectivesStandards Page Induction Heating Hazards Symbol UsageElectric Shock can kill Fumes and Gases can be hazardous California Proposition 65 Warnings About Implanted Medical Devices Principal Safety Standards EMF Information − Consignes DE Sécurité − Lire Avant Utilisation Signification des symbolesUNE Décharge Électrique peut entraîner la mort LES Fumées ET LES GAZ peuvent être dangereux LE Chauffage PAR Induction peut provoquer des brûlures Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser DES Organes Mobiles peuvent provoquer des blessures En ce qui concerne les implants médicaux Proposition californienne 65 AvertissementsPrincipales normes de sécurité Information EMF − Definitions Power before working on Shown by the symbolsAre possible hazards as Kill Weee Label For Products Sold Within The EU Rating Label For CE Products Symbols And Definitions − InstallationSpecifications I1max Selecting a Location Do not move or operate unit where it could tipTipping Movement Location And Airflow Phase Input Voltage Electrical Service Guide50 Hz Three Min Grounding Conductor Size In AWG Welding Power Source Input Power Connections Connecting 3-Phase Input Power For 460/575 Volt ModelsDisconnect Device Input Power Connections GND/PE Earth Ground Connecting 3-Phase Input Power For 400/460 Volt Models Power Source Output Connections Socket Socket Information Remote 14 Receptacle RC14 Information and ConnectionsRemote 14 Socket Information Signal Common Temperature Recorder Socket InformationSocket No Socket Information Unused Receptacles Plug Secondary Insulation ProtectionHandle Magnet Workpiece Use handle to place magnet on the workpiece Locating Thermocouples Volt AC Duplex Receptacle And Supplementary Protector Other end is fitted with a 2-pin type K connector Attaching Welded Thermocouples Do not weld thermocouples while connected to power source Placing Temperature Probe Using Contact Thermocouples Controls − Components and Controls Safety Equipment − Setup and OperationPower Source/System Setup System Description OM-222 166 Mode....... Preheat Control TC Temperature Soak Time Temperature-Based ControlDecrease button to change the value to the desired setting Programming Pwht Post-Weld Heat Treat Bake-Out Custom Program Soak Parameters End Custom ProgramType.......Step 600 Number OM-222 166 Ramp Temperature 600 Ramp Rate 600 /Hr Soak Function SoakNumber End Function Soak at 1250 degrees F for a period Manual ControlTypical 5-Segment Custom Program Run Status Temperature Based ControlTC5 Target Temp −−−− TC6 Countdown.. −−−−−− Preheat, Bake-Out And Pwht Run Status Screen Parameters Power TC5 Current TC6 Voltage Frequency KHzCooler Cooler cannot be turned off while output is on Program run is initiated, the Run Must be running to enter Hold modeReal-Time Operation Button. a change of program parameters Power Source Output Characteristics System Operating CharacteristicsAir Cooled Output Liquid Cooled Output Routine Maintenance − MaintenanceDisconnect power Before maintaining Servicing Hazards − Safety Precautions for Servicing California Proposition 65 Warnings Operator Interface Indicators − Diagnostics & Troubleshooting Limit Condition Codes Limit ConditionsRun Status Limit Condition Additional Information Fault Condition Additional Information Fault ConditionsFault Condition Codes ClrSts Flowing System Diagnostic ScreensOff Cable1 LQD DIAG1 OutI1 Cable2 LQD OutI2 ClntFR 0.75 GPM Therm2 Therm1Therm3 VBus Tools Needed 16, 3/8 Turn Off welding power source, and disconnect input powerRemoving Wrapper and Measuring Input Capacitor Voltage Blowing Out Inside Of Unit Material Thickness Reference Chart Circuit Diagram − Electrical Diagram 218 057-G See Figure 11-313 11-2 − Parts List Front Panel Rear Panel Base w/Components Top Windtunnel Capacitor Assembly Right Windtunnel 229 Right Windtunnel 400 V Model Only 208 Left Windtunnel PLG14 10. Hermaphroditic Blank Plug Assy SOCKET/WRENCH Selection Table Standard Metric OM-222 166 Support ServiceYour distributor also gives Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s