Therm1, Therm2, Therm3, VBus, Off | Miller Electric ProHeat 35

SOPEN − no cable or plug in place

ClntFR − This is the coolant flow rate (in GPM) from the cooler on a liquid-cooled system.

ClrSts − This is the status of the cooler. Possible labels:

SOff

SFlowing

The second diagnostic screen is available by again pressing and holding the Run Status

button and pressing the Parameters

button.

kW V HzA

		System Diagnostic Screen
VLnA−B: 460V		Therm1:	75		DIAG2
VLnB−C: 460V		Therm2:	75	Therm5: OPEN
VLnC−A:	460V	Therm3:	75	ClrTmp:	77
VBus:	650V	Therm4: OPEN		RmtFlw:	Off

VLnA-B − This is the phase to phase line voltage between phases A and B.

VLnB-C − This is the phase to phase line voltage between phases B and C.

VLnC-A − This is the phase to phase line voltage between phases C and A.

VBus − This is the DC bus voltage.

Therm1 − This is the temperature of the current source primary heatsink.

Therm2 − This is the temperature of the bridge heatsink.

Therm3 − This the the temperature of the current source secondary heatsink.

Therm4 − Open (not used).

Therm5 − Open (not used).

ClrTmp − This is the temperature of the coolant on a liquid-cooled system.

SOPEN − no cooler is detected.

RmtFlw − This is the status of the relay contacts for remote coolant flow on a liquid-cooled system.

SOFF

SON

.RmtFlw feature is unsupported on the current platform.

OM-222 166 Page 45

Image 51

Miller Electric ProHeat 35 manual Therm1, Therm2, Therm3, VBus, Therm4 Open, Off

Contents

OM-222 166K 2007−11 Processes DescriptionFile Induction Heating From Miller to You Table of Contents EMF Information − MaintenanceRoutine Maintenance Blowing Out Inside Of Unit Limit Conditions Limit Condition Codes Fault Conditions Directives StandardsDecstat1/07 Page Fumes and Gases can be hazardous Symbol UsageInduction Heating Hazards Electric Shock can kill California Proposition 65 Warnings About Implanted Medical Devices Principal Safety Standards EMF Information LES Fumées ET LES GAZ peuvent être dangereux Signification des symboles− Consignes DE Sécurité − Lire Avant Utilisation UNE Décharge Électrique peut entraîner la mort DES Organes Mobiles peuvent provoquer des blessures Risque D’INCENDIE OU D’EXPLOLE Chauffage PAR Induction peut provoquer des brûlures LA Chute DE L’APPAREIL peut blesser Proposition californienne 65 Avertissements Principales normes de sécurité Information EMFEn ce qui concerne les implants médicaux − Definitions Kill Shown by the symbolsPower before working on Are possible hazards as Weee Label For Products Sold Within The EU Rating Label For CE Products I1max − InstallationSymbols And Definitions Specifications Movement Location And Airflow Do not move or operate unit where it could tipSelecting a Location Tipping Min Grounding Conductor Size In AWG Electrical Service GuidePhase Input Voltage 50 Hz Three GND/PE Earth Ground Connecting 3-Phase Input Power For 460/575 Volt ModelsWelding Power Source Input Power Connections Disconnect Device Input Power Connections Connecting 3-Phase Input Power For 400/460 Volt Models Power Source Output Connections Remote 14 Receptacle RC14 Information and Connections Remote 14 Socket InformationSocket Socket Information Unused Temperature Recorder Socket InformationSignal Common Socket No Socket Information Workpiece Use handle to place magnet on the workpiece Secondary Insulation ProtectionReceptacles Plug Handle Magnet Locating Thermocouples Volt AC Duplex Receptacle And Supplementary Protector Other end is fitted with a 2-pin type K connector Attaching Welded Thermocouples Do not weld thermocouples while connected to power source Placing Temperature Probe Using Contact Thermocouples Controls − Components and Controls System Description − Setup and OperationSafety Equipment Power Source/System Setup OM-222 166 Programming Temperature-Based ControlMode....... Preheat Control TC Temperature Soak Time Decrease button to change the value to the desired setting Pwht Post-Weld Heat Treat Bake-Out Custom Program Soak Parameters 600 Custom ProgramEnd Type.......Step Number OM-222 166 Ramp Temperature 600 Ramp Rate 600 /Hr End Function SoakSoak Function Number Manual Control Typical 5-Segment Custom ProgramSoak at 1250 degrees F for a period Preheat, Bake-Out And Pwht Run Status Screen Temperature Based ControlRun Status TC5 Target Temp −−−− TC6 Countdown.. −−−−−− Cooler cannot be turned off while output is on Power TC5 Current TC6 Voltage Frequency KHzParameters Cooler Must be running to enter Hold mode Real-Time OperationProgram run is initiated, the Run Button. a change of program parameters Liquid Cooled Output System Operating CharacteristicsPower Source Output Characteristics Air Cooled Output Before maintaining − MaintenanceRoutine Maintenance Disconnect power Servicing Hazards − Safety Precautions for Servicing California Proposition 65 Warnings Operator Interface Indicators − Diagnostics & Troubleshooting Limit Condition Additional Information Limit ConditionsLimit Condition Codes Run Status Fault Conditions Fault Condition CodesFault Condition Additional Information System Diagnostic Screens Off Cable1 LQD DIAG1 OutI1 Cable2 LQD OutI2 ClntFR 0.75 GPMClrSts Flowing VBus Therm1Therm2 Therm3 Turn Off welding power source, and disconnect input power Removing Wrapper and Measuring Input Capacitor VoltageTools Needed 16, 3/8 Blowing Out Inside Of Unit Material Thickness Reference Chart Circuit Diagram − Electrical Diagram 218 057-G See Figure 11-313 11-2 − Parts List Front Panel Rear Panel Base w/Components Top Windtunnel Capacitor Assembly Right Windtunnel 229 Right Windtunnel 400 V Model Only 208 Left Windtunnel PLG14 10. Hermaphroditic Blank Plug Assy SOCKET/WRENCH Selection Table Standard Metric OM-222 166 Service Your distributor also givesSupport Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact