Miller Electric ProHeat 35 guide

Notes

SOCKET/WRENCH SELECTION TABLE				SOCKET/WRENCH SELECTION TABLE
	(U.S. STANDARD)				(METRIC)

Specifications		Socket or Wrench Size		Specifications		Socket or Wrench Size

Bolt	Decimal	Bolt	Nut	Bolt	U.S.
Bolt	Decimal			Bolt	Decimal	Bolt	Nut
Diameter	Equivalent			Diameter	Decimal	Bolt	Nut
Diameter	Equivalent			Diameter	Equivalent
					Equivalent

1/4 in	.250 in	3/8 in	7/16 in	6 mm	.2362 in	10 mm	10 mm

5/16 in	.3125 in	1/2 in	9/16 in	8 mm	.3150 in	14 mm	14 mm

3/8 in	.375 in	9/16 in	5/8 in	10 mm	.3937 in	17 mm	17 mm

7/16 in	.4375 in	5/8 in	3/4 in	12 mm	.4724 in	19 mm	19 mm

1/2 in	.500 in	3/4 in	13/16 in	14 mm	.5512 in	22 mm	22 mm

9/16 in	.5625 in	7/8 in	7/8 in	16 mm	.6299 in	24 mm	24 mm

5/8 in	.625 in	15/16 in	1 in	18 mm	.7087 in	27 mm	27 mm

3/4 in	.750 in	1-1/8 in	1-1/8 in	22 mm	.8661 in	32 mm	32 mm

7/8 in	.875 in	1-5/16 in	1-5/16 in	24 mm	.9449 in	36 mm	36 mm

1 in	1.000 in	1-1/2 in	1-1/2 in

OM-222 166 Page 63

Page 69

Image 69

Miller Electric ProHeat 35 manual SOCKET/WRENCH Selection Table Standard Metric

Contents

OM-222 166K 2007−11 Processes DescriptionFile Induction Heating From Miller to You Table of Contents Routine Maintenance Blowing Out Inside Of Unit − MaintenanceLimit Conditions Limit Condition Codes Fault Conditions EMF Information Directives StandardsDecstat1/07 Page Induction Heating Hazards Symbol UsageElectric Shock can kill Fumes and Gases can be hazardous California Proposition 65 Warnings About Implanted Medical Devices Principal Safety Standards EMF Information − Consignes DE Sécurité − Lire Avant Utilisation Signification des symbolesUNE Décharge Électrique peut entraîner la mort LES Fumées ET LES GAZ peuvent être dangereux LE Chauffage PAR Induction peut provoquer des brûlures Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser DES Organes Mobiles peuvent provoquer des blessures Proposition californienne 65 Avertissements Principales normes de sécurité Information EMFEn ce qui concerne les implants médicaux − Definitions Power before working on Shown by the symbolsAre possible hazards as Kill Weee Label For Products Sold Within The EU Rating Label For CE Products Symbols And Definitions − InstallationSpecifications I1max Selecting a Location Do not move or operate unit where it could tipTipping Movement Location And Airflow Phase Input Voltage Electrical Service Guide50 Hz Three Min Grounding Conductor Size In AWG Welding Power Source Input Power Connections Connecting 3-Phase Input Power For 460/575 Volt ModelsDisconnect Device Input Power Connections GND/PE Earth Ground Connecting 3-Phase Input Power For 400/460 Volt Models Power Source Output Connections Remote 14 Receptacle RC14 Information and Connections Remote 14 Socket InformationSocket Socket Information Signal Common Temperature Recorder Socket InformationSocket No Socket Information Unused Receptacles Plug Secondary Insulation ProtectionHandle Magnet Workpiece Use handle to place magnet on the workpiece Locating Thermocouples Volt AC Duplex Receptacle And Supplementary Protector Other end is fitted with a 2-pin type K connector Attaching Welded Thermocouples Do not weld thermocouples while connected to power source Placing Temperature Probe Using Contact Thermocouples Controls − Components and Controls Safety Equipment − Setup and OperationPower Source/System Setup System Description OM-222 166 Mode....... Preheat Control TC Temperature Soak Time Temperature-Based ControlDecrease button to change the value to the desired setting Programming Pwht Post-Weld Heat Treat Bake-Out Custom Program Soak Parameters End Custom ProgramType.......Step 600 Number OM-222 166 Ramp Temperature 600 Ramp Rate 600 /Hr Soak Function SoakNumber End Function Manual Control Typical 5-Segment Custom ProgramSoak at 1250 degrees F for a period Run Status Temperature Based ControlTC5 Target Temp −−−− TC6 Countdown.. −−−−−− Preheat, Bake-Out And Pwht Run Status Screen Parameters Power TC5 Current TC6 Voltage Frequency KHzCooler Cooler cannot be turned off while output is on Must be running to enter Hold mode Real-Time OperationProgram run is initiated, the Run Button. a change of program parameters Power Source Output Characteristics System Operating CharacteristicsAir Cooled Output Liquid Cooled Output Routine Maintenance − MaintenanceDisconnect power Before maintaining Servicing Hazards − Safety Precautions for Servicing California Proposition 65 Warnings Operator Interface Indicators − Diagnostics & Troubleshooting Limit Condition Codes Limit ConditionsRun Status Limit Condition Additional Information Fault Conditions Fault Condition CodesFault Condition Additional Information System Diagnostic Screens Off Cable1 LQD DIAG1 OutI1 Cable2 LQD OutI2 ClntFR 0.75 GPMClrSts Flowing Therm2 Therm1Therm3 VBus Turn Off welding power source, and disconnect input power Removing Wrapper and Measuring Input Capacitor VoltageTools Needed 16, 3/8 Blowing Out Inside Of Unit Material Thickness Reference Chart Circuit Diagram − Electrical Diagram 218 057-G See Figure 11-313 11-2 − Parts List Front Panel Rear Panel Base w/Components Top Windtunnel Capacitor Assembly Right Windtunnel 229 Right Windtunnel 400 V Model Only 208 Left Windtunnel PLG14 10. Hermaphroditic Blank Plug Assy SOCKET/WRENCH Selection Table Standard Metric OM-222 166 Service Your distributor also givesSupport Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s

SOCKET/WRENCH SELECTION TABLE

(U.S. STANDARD)

(METRIC)

OM-222 166 Page 63