Mitsubishi Electronics FR-A500L instruction manual F4 fourth frequency voltage

PARAMETERS

Func-	Parameter			Minimum	Factory Setting	Refer To
		Name	Setting Range	Setting		Page:
tion	Number
				Increments		<Note9>
flexiblepoint-5V/F characteristics	107	V/F4 (fourth frequency voltage)	0 to 1000V	0.1V	0	98
		(Note 1)
	108	V/F5 (fifth frequency) (Note 1)	0 to 400Hz, 9999	0.01Hz	9999	98
	109	V/F5 (fifth frequency voltage)	0 to 1000V	0.1V	0	98
		(Note 1)
	110	Third acceleration/deceleration time	0 to 3600 sec/	0.1 sec/	9999	99
			0 to 360 sec, 9999	0.01 sec
functions	111	Third deceleration time	0 to 3600 sec/	0.1 sec/	9999	99
			0 to 360 sec, 9999	0.01 sec
	112	Third torque boost (Note 1)	0 to 30.0%, 9999	0.1%	9999	99
Third	113	Third V/F (base frequency) (Note 1)	0 to 400Hz, 9999	0.01Hz	9999	99
	*114	Third stall prevention operation current	0 to 150%	0.1%	150%	99
	115	Third stall prevention operation frequency	0 to 400Hz	0.01Hz	0	99
	116	Third output frequency detection	0 to 400Hz, 9999	0.01Hz	9999	99
functions	117	Station number	0 to 31	1	0	99
			10, 11 (data length 7)
	118	Communication speed	48, 96, 192	1	192	99
	119	Stop bit length/data length	0, 1 (data length 8)	1	1	99
Communication
	120	Parity check presence/absence	0, 1, 2	1	2	99
	121	Number of communication retries	0 to 10, 9999	1	1	99
	122	Communication check time interval	0, 0.1 to 999.8 sec,	0.1	0<9999>	99
			9999
	123	Waiting time setting	0 to 150ms, 9999	10ms	9999	99
	124	CR, LF presence/absence selection	0,1,2	1	1	99
	128	PID action selection	10, 11, 20, 21	1	10	109
control	129	PID proportional band	0.1 to 1000%, 9999	0.1%	100%	109
	131	Upper limit	0 to 100%, 9999	0.1%	9999	109
	130	PID integral time	0.1 to 3600 sec, 9999	0.1 sec	1 sec	109
PID
	132	Lower limit	0 to 100%, 9999	0.1%	9999	109
	133	PID action set point for PU operation	0 to 100%	0.01%	0%	109
	134	PID differential time	0.01 to 10.00 sec, 9999	0.01 sec	9999	109
Commercialpower supply- inverterswitch-over		Commercial power supply-inverter
	135	switch-over sequence output terminal	0, 1, 2	1	0	116
		selection
	136	MC switch-over interlock time	0 to 100.0 sec	0.1 sec	1.0 sec	116
		supply switch-over frequency
	137	Start waiting time	0 to 100.0 sec	0.1 sec	0.5 sec	116
	138	Commercial power supply-inverter	0, 1	1	0	116
		switch-over selection at alarm occurrence
	139	Automatic inverter-commercial power	0 to 60.00Hz, 9999	0.01Hz	9999	116
	140	Backlash acceleration stopping	0 to 400Hz	0.01Hz	1.00Hz	119
		frequency (Note 7)
Backlash	141	Backlash acceleration stopping time	0 to 360 sec	0.1 sec	0.5 sec	119
		(Note 7)
	142	Backlash deceleration stopping	0 to 400Hz	0.01Hz	1.00Hz	119
		frequency (Note 7)
	143	Backlash deceleration stopping time	0 to 360 sec	0.1 sec	0.5 sec	119
		(Note 7)
Display	144	Speed setting switch-over	0, 2, 4, 6, 8, 10, 102,	1	4	119
			104, 106, 108, 110
Additional functions	*149	Stall prevention level at 10V input	0 to 150%	0.1%	150%	58
	*148	Stall prevention level at 0V input	0 to 150%	0.1%	120%	58

20