Manuals / Mitsubishi Electronics / Computer Equipment / Modem

Mitsubishi Electronics MIM-G01 manual Super Modem 56k MIM-A01, Interfaces and Connectors

Models: MIM-G01 MIM-A01

1 62

Page 17

Mounting and Installation	Super Modem 56k (MIM-A01)

3.2Super Modem 56k (MIM-A01)

The MIM-A01 is a PSTN modem intended for transmission of data, SMS, e-mail and fax mes- sages by analog telephone networks and complies to the high speed standard of V.90 and 56k. It is suitable for DIN-Rail mounting inside control boxes.

3.2.1Interfaces and Connectors

SUPER MODEM

Power

Line




Fig. 3-6:	Overview of all connectors of the Super Modems 56k

Nr.	Description	Meaning
	Line	Telephone jack RJ11

	10...30VDC	Power supply (2 screw terminals) and power supply jack

	Service	Button

	LEDs	LEDs (Power, Mail in, Line, Mail out und Modem Mode)

	RS232 Interface	9pin D-Sub jack

NOTE

Tab. 3-4:Description of the connectors of the Modems

For connecting the modem to a PC, a 1:1 serial standard cable is to be used. For information to connect a PLC, refer to the PLC documentation.

Mitsubishi Industrial Modem

3 - 7

Page 17

Image 17

Mitsubishi Electronics MIM-G01 manual Super Modem 56k MIM-A01, Interfaces and Connectors

Contents

MITSUBISHI ELECTRIC INDUSTRIAL AUTOMATION MITSUBISHI ELECTRICMitsubishi MIM series DraftPage About this Manual Page Industrial Modems MIM-A01 and MIM-G0 Instruction ManualArt-No VersionMITSUBISHI ELECTRIC Safety instructions Security AdviceIntended Target Audience Proper useMITSUBISHI ELECTRIC 4 Power supply 5 Operation 3 Mounting and Installation1 Mitsubishi Industrial Modems at a glance 2 Equipment Versions7 Technical Data 6 Configuration8 Appendix MITSUBISHI ELECTRIC1.1 Mitsubishi Normal Modem GSM MIM-G01 1 Mitsubishi Industrial Modems at a glance1.2 Mitsubishi Super Modem 56k MIM-A01 Express E-Mail2 Equipment Versions 2.2 Teleservice via PCModem Typ MITSUBISHI ELECTRIC3.1.1 Interfaces and Connectors 3 Mounting and Installation3.1 Normal Modem GSM MIM-G01 Power supply 2 screw terminalsFig. 3-2 LEDs on the MIM-G01 3.1.2 Meaning of the LEDsTab. 3-3 Two LEDs are used to show the state of the modem MITSUBISHI ELECTRICPush down the button until the card holder is released 3.1.3 Connecting the GSM antenna3.1.4 Inserting the SIM card E ATTENTION PowerMITSUBISHI ELECTRIC AntennaSUPER MODEM 3.2.1 Interfaces and Connectors3.2 Super Modem 56k MIM-A01 Power 3.2.2 Meaning of the LEDsMITSUBISHI ELECTRIC Line3.2.3 Connection to the Telephone Network 3.2.4 Testing the Telephone Connection3.2.5 Telephone Exchange System 6 5 4 3 2 1 5 - EE ATTENTION 3.3 MountingP DANGER MITSUBISHI ELECTRICP DANGER 4 Power supplyE ATTENTION 5.1 MIM-G01 5 Operation5.2 MIM-A01 MITSUBISHI ELECTRIC6.1.1 Project Settings 6 Configuration6.1 MIM and Mitsubishi ALPHA XL ATE0S0=2&S0+IFC=0,0+CMEE=1+IPR=9600+CICB=0&W6.1.2 Function Block SMS send SMS Service CenterGSM SMS Short Message Service SMS SettingRecipient ATE0S0=2&S0+IFC=0,0+CMEE=1+IPR=9600+CICB=0&W 6.1.3 PLC ConnectionATE0S0=2Q1+D0\Q0\J0&W Initialisation of a GSM Modem6.2 MIM and Mitsubishi MELSEC FX 6.2.2 MIM for FX Remote Access6.3 Connection to other Mitsubishi Products 6.2.1 MIM-G01 and FX MessengerMITSUBISHI ELECTRIC 6.4.1 Time delays during modem transmissions6.4 RS 232-Transparent-Mode TransMode AT+T SEND=TransMode 6.4.2 TransMode Command6.4.3 TransMode Login Command MITSUBISHI ELECTRIC Login without parametersLogin with password and parameters Main Features 7 Technical DataSystem Architecture Telephone- /GSM NetworkGeneral Data FirmwareFeatures Features7.1.1 MIM-G01 7.1 DimensionsPower NORMAL MODEMService 7.1.2 MIM-A01Power SUPER MODEM 56k8.1.1 Important AT Commands 8.1 AT Commands MIM-G01+CSQ - Signal Quality 8 AppendixExample +CNUM - Own Number+CSCA - SMS Center Number number+IFC - Flow Control +ICF - Data FormatDCEbyDTE DTEbyDCEstat +COPS - GSM Network+CMGS - Send SMS modeV24-V35 Commands 8.1.2 Overview of AT-CommandsService Commands General Commands Dial CommandsNetwork SecurityData Commands SMS CommandsPhonebook Tab. 8-17 SMS CommandsFax Commands CLASS2 Fax Commands CLASS1Special AT Commands Fax Commands CLASS18.2.1 Overview of AT Commands 8.2 AT Commands MIM-A01+TFORMAT - Sets the data format 8.2.2 AT Command Descriptions+TBAUD - Set the baudrate K - Select Serial Port Flow ControlE - Command Mode Echo D - Dial CommandH - Switch Hook Control Q - Result Code Display Control8.2.3 Overview of S-Registers +VCID - Caller ID SettingsW - Store Active Profile Tab. 8-24 Overview of S-Registers8.2.4 Message CommandsOverview of the Commands Sending a Fax Setting General Message ParametersNo message text can be entered after this command MITSUBISHI ELECTRICCTRL+Z Sending an SMS MessageExample CTRL+ZMITSUBISHI ELECTRIC Sending an Express E-MailAT+T Send=Express To Recipient Dial NumberFrom Sender Subject MessageText line#1 MessageText line#n CTRL+ZTo info@example.net PPPUser 00012345678445566 PPPPassword Rose Sending Internet E-Mail SMTPSubject ExampleMITSUBISHI ELECTRIC Retrieving Internet E-Mail POP3START CTRL+Z ExampleAT+TList - Displaying Received Messages 8.2.6 Message CommandsAT+T Delete - Deleting a Stored Message ResponseMITSUBISHI ELECTRIC AT+T Read - Reading a Stored MessageLists the message with the indicated ID from the memory of the modem The message is not deleted and can be read as often as you wantAT+T Answer - Setting the Response Behaviour 8.2.7 Modem CommandsAT+T Time - Setting the System Time Call answering on defaultAT+T Verbose - Switching Comprehensive Responses On or Off AT+T Echo - Switching the Echo On or OffReading the Current System Time Switches the echo for keyboard input on or offAT+T Erase - Resetting the Modem AT+T Help - Showing a Command OverviewAT+T Mode - Activating Modem Mode or Message Mode AT+T RedialAT+T DialRules - Dial Method, Dial Tone Detection AT+T RedialDelayDelay 600 delay in seconds default=90Volume AT+ T Speaker - Adjusting the Modem Speaker VolumeVolume switches the speaker offIndex Page MITSUBISHI ELECTRIC INDUSTRIAL AUTOMATION MITSUBISHI ELECTRICHEADQUARTERS MIDDLE EAST REPRESENTATIVES