Manuals / Mitsubishi Electronics / Computer Equipment / Modem

Mitsubishi Electronics MIM-A01 manual Login without parameters, Login with password and parameters

Models: MIM-G01 MIM-A01

1 62

Page 30

RS 232-Transparent-Mode (TransMode)		Configuration

Login without parameters
[password]	Login with password
[ ]	Login without password

Login with password and parameters

[password; Format:format; Handshake:handshake; Keep:timeout; Baudrate: RS232Speed]

For a description of the parameters, see Section 6.4.2

The configuration of the Mitsubishi Super Modem should be done locally during set-up, tested and only then approved for remote dial-in.

The remote modification of the parameters overwrites the previously configured – and tested - parameters

The remote modification of the parameters should only be used if it is absolutely necessary.

It can also be used to exclude possible local modifications.

6 - 8

MITSUBISHI ELECTRIC

Page 30

Image 30

Mitsubishi Electronics MIM-A01, MIM-G01 Login without parameters, Login with password and parameters, Mitsubishi Electric

Contents

Mitsubishi MIM series MITSUBISHI ELECTRICMITSUBISHI ELECTRIC INDUSTRIAL AUTOMATION DraftPage About this Manual Page Art-No Instruction ManualIndustrial Modems MIM-A01 and MIM-G0 VersionMITSUBISHI ELECTRIC Intended Target Audience Security AdviceSafety instructions Proper useMITSUBISHI ELECTRIC 1 Mitsubishi Industrial Modems at a glance 3 Mounting and Installation4 Power supply 5 Operation 2 Equipment Versions8 Appendix 6 Configuration7 Technical Data MITSUBISHI ELECTRIC1.2 Mitsubishi Super Modem 56k MIM-A01 1 Mitsubishi Industrial Modems at a glance1.1 Mitsubishi Normal Modem GSM MIM-G01 Express E-MailModem Typ 2.2 Teleservice via PC2 Equipment Versions MITSUBISHI ELECTRIC3.1 Normal Modem GSM MIM-G01 3 Mounting and Installation3.1.1 Interfaces and Connectors Power supply 2 screw terminalsTab. 3-3 Two LEDs are used to show the state of the modem 3.1.2 Meaning of the LEDsFig. 3-2 LEDs on the MIM-G01 MITSUBISHI ELECTRIC3.1.3 Connecting the GSM antenna 3.1.4 Inserting the SIM cardPush down the button until the card holder is released MITSUBISHI ELECTRIC PowerE ATTENTION Antenna3.2.1 Interfaces and Connectors 3.2 Super Modem 56k MIM-A01SUPER MODEM MITSUBISHI ELECTRIC 3.2.2 Meaning of the LEDsPower Line3.2.5 Telephone Exchange System 3.2.4 Testing the Telephone Connection3.2.3 Connection to the Telephone Network 6 5 4 3 2 1 5 - EP DANGER 3.3 MountingE ATTENTION MITSUBISHI ELECTRIC4 Power supply E ATTENTIONP DANGER 5.2 MIM-A01 5 Operation5.1 MIM-G01 MITSUBISHI ELECTRIC6.1 MIM and Mitsubishi ALPHA XL 6 Configuration6.1.1 Project Settings ATE0S0=2&S0+IFC=0,0+CMEE=1+IPR=9600+CICB=0&WGSM SMS Short Message Service SMS Service Center6.1.2 Function Block SMS send SMS SettingRecipient ATE0S0=2Q1+D0\Q0\J0&W 6.1.3 PLC ConnectionATE0S0=2&S0+IFC=0,0+CMEE=1+IPR=9600+CICB=0&W Initialisation of a GSM Modem6.3 Connection to other Mitsubishi Products 6.2.2 MIM for FX Remote Access6.2 MIM and Mitsubishi MELSEC FX 6.2.1 MIM-G01 and FX Messenger6.4.1 Time delays during modem transmissions 6.4 RS 232-Transparent-Mode TransModeMITSUBISHI ELECTRIC 6.4.2 TransMode Command 6.4.3 TransMode Login CommandAT+T SEND=TransMode Login without parameters Login with password and parametersMITSUBISHI ELECTRIC System Architecture 7 Technical DataMain Features Telephone- /GSM NetworkFeatures FirmwareGeneral Data FeaturesPower 7.1 Dimensions7.1.1 MIM-G01 NORMAL MODEMPower 7.1.2 MIM-A01Service SUPER MODEM 56k+CSQ - Signal Quality 8.1 AT Commands MIM-G018.1.1 Important AT Commands 8 Appendix+CSCA - SMS Center Number +CNUM - Own NumberExample numberDCEbyDTE +ICF - Data Format+IFC - Flow Control DTEbyDCE+CMGS - Send SMS +COPS - GSM Networkstat mode8.1.2 Overview of AT-Commands Service CommandsV24-V35 Commands Network Dial CommandsGeneral Commands SecurityPhonebook SMS CommandsData Commands Tab. 8-17 SMS CommandsSpecial AT Commands Fax Commands CLASS1Fax Commands CLASS2 Fax Commands CLASS18.2 AT Commands MIM-A01 8.2.1 Overview of AT Commands+TBAUD - Set the baudrate 8.2.2 AT Command Descriptions+TFORMAT - Sets the data format K - Select Serial Port Flow ControlH - Switch Hook Control D - Dial CommandE - Command Mode Echo Q - Result Code Display ControlW - Store Active Profile +VCID - Caller ID Settings8.2.3 Overview of S-Registers Tab. 8-24 Overview of S-RegistersMessage Commands Overview of the Commands8.2.4 No message text can be entered after this command Setting General Message ParametersSending a Fax MITSUBISHI ELECTRICExample Sending an SMS MessageCTRL+Z CTRL+ZAT+T Send=Express To Recipient Dial NumberFrom Sender Subject Sending an Express E-MailMITSUBISHI ELECTRIC MessageText line#1 MessageText line#n CTRL+ZSubject Sending Internet E-Mail SMTPTo info@example.net PPPUser 00012345678445566 PPPPassword Rose ExampleSTART CTRL+Z Retrieving Internet E-Mail POP3MITSUBISHI ELECTRIC ExampleAT+T Delete - Deleting a Stored Message 8.2.6 Message CommandsAT+TList - Displaying Received Messages ResponseLists the message with the indicated ID from the memory of the modem AT+T Read - Reading a Stored MessageMITSUBISHI ELECTRIC The message is not deleted and can be read as often as you wantAT+T Time - Setting the System Time 8.2.7 Modem CommandsAT+T Answer - Setting the Response Behaviour Call answering on defaultReading the Current System Time AT+T Echo - Switching the Echo On or OffAT+T Verbose - Switching Comprehensive Responses On or Off Switches the echo for keyboard input on or offAT+T Mode - Activating Modem Mode or Message Mode AT+T Help - Showing a Command OverviewAT+T Erase - Resetting the Modem AT+T RedialDelay AT+T RedialDelayAT+T DialRules - Dial Method, Dial Tone Detection 600 delay in seconds default=90Volume AT+ T Speaker - Adjusting the Modem Speaker VolumeVolume switches the speaker offIndex Page HEADQUARTERS MITSUBISHI ELECTRICMITSUBISHI ELECTRIC INDUSTRIAL AUTOMATION MIDDLE EAST REPRESENTATIVES