When PLASMA/WASH lamp flashes
wThe power failure mode for PLASMA DEODORIZING power is memorized when the failure mode is called.
F Check of PLASMA DEODORIZING power
After performing the check, make sure to release the failure mode recall function.
Turn ON the power supply.
While the operation is being
stopped, doesYes PLASMA/WASH lamp flash
twice?
No
Make sure that the front panel is firmly closed.
1During pressing both OPERATION SELECT button and TOO COOL button on the remote controller at the same time, press RESET button.
2First, release RESET button.
And release the other two buttons since all LCD in operation display section of the remote controller is displayed after 3 seconds. (Failure mode recall function is set.)
3Press OPERATE/STOP (ON/OFF) button.
4 After a short beep sound is emitted, press once PLASMA button.
PLASMA DEODORIZING operation is selected.
wThe plasma power operation check mode is set.(Refer to
High voltage (approx.
Pay careful attention and never touch PLASMA/WASH unit and the
Replace the indoor electronic control P.C. board is out of order.
1 During pressing both OPERATION SELECT button and TOO COOL button on the remote controller at the same time, press RESET button.
2 First, release RESET button.
And release the other two buttons since all LCD in operation display section of the remote controller is displayed after 3 seconds. (Failure mode recall function is set.)
3 Press OPERATE/STOP (ON/OFF) button.
4 After a short beep sound is emitted, press once PLASMA button.
PLASMA DEODORIZING operation is selected.
PLASMA DEODORIZING operation
Does PLASMA/WASH lamp stay OFF, or continuously flash?
Continuously flashes.
Stays OFF | PLASMA DEODORIZING power supply is normal. | |
|
| The front panel is not firmly closed, therefore the |
|
| |
|
| protection by the interlock switch is active. |
|
|
|
w1 Turn PLASMA DEODORIZING power OFF and ON again. (For turning off PLASMA DEODORIZING power, refer to
(If it goes normal without turning OFF and ON, PLASMA/WASH lamp doesn't go OFF.
| Remove the plasma unit, firmly close the |
|
|
| If the plasma unit is dirty, clean the unit. |
| |||||
|
|
|
| After cleaning, make sure to attach the unit when it is |
| ||||||
| front panel, and then perform PLASMA |
| Stays OFF |
| |||||||
|
| completely dry. |
| ||||||||
| DEODORIZING power operation check (w1). |
|
|
|
|
| |||||
|
|
|
|
| If the air conditioner goes ON with the plasma unit |
| |||||
| Does PLASMA/WASH lamp stay OFF, or |
|
|
|
| ||||||
|
|
|
| being wet, protection gets active and PLASMA/WASH |
| ||||||
| continuously flash? |
|
|
|
| ||||||
|
|
|
| lamp continuously flashes. |
| ||||||
|
|
|
|
|
|
|
|
| |||
|
| Continuously flashes. |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |||
| Turn OFF the power supply, and check the |
| No |
|
|
|
| ||||
| SAFETY DEVICE(PLASMA UNIT). |
|
|
| Firmly fix the SAFETY DEVICE. |
| |||||
|
|
|
|
|
|
| |||||
| Is it firmly fixed? |
|
|
|
|
|
|
| |||
|
| Yes |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |||
Turn ON and OFF the SAFETY DEVICE |
| No |
|
|
|
| |||||
(PLASMA UNIT) using something like a screw |
|
|
|
|
| ||||||
driver, and measure the resistance value between |
|
|
| Replace the SAFETY DEVICE(PLASMA UNIT). |
|
| |||||
|
|
|
|
| |||||||
CN1T2 1 and 3 on the indoor electronic control |
|
|
|
|
|
|
| ||||
P.C. board. Does the switch work? |
|
|
|
|
|
|
| ||||
|
| Yes |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |||
| Keep the SAFETY DEVICE(PLASMA UNIT) |
| No |
|
|
|
| ||||
| ON using something like a screw driver. |
|
|
|
|
| |||||
|
| 9.5V DC is generated. | |||||||||
| Turn ON the power supply. |
| |||||||||
| While the operation is being stopped, is the |
|
|
| Replace the indoor electronic control P.C. board. |
|
| ||||
|
|
|
|
|
| ||||||
| voltage between CN1 1(+) and 2(GND) |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| ||||
| on the PLASMA POWER P.C. board |
|
|
|
|
|
|
| |||
| (PLASMA DEODORIZING) 0V? |
|
|
|
|
|
|
| |||
|
| Yes |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Set the plasma power failure mode recall function. |
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| When PLASMA button is pressed, is |
| No | Replace the indoor electronic control P.C. board. | |||||||
| there voltage of 12.5V DC between CN1 |
|
|
| Check the wiring of CN1T1 on the indoor electronic control | ||||||
|
|
|
| ||||||||
| 1(+) and 2(GND)? |
|
|
| P.C. board. | ||||||
|
| Yes |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| Replace the PLASMA POWER P.C. board |
|
|
|
|
|
|
|
|
| |
| (PLASMA DEODORIZING). |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
26
