Plate, Hole | Mitsubishi Electronics PUHY-YMC instruction

ENGLISH

2.The control box cover is removed by removing the 2 screws and pull- ing downward. (The control box with the cover removed is shown in the figure below.)

3.Method of using conduit mounting plate

The equipment includes conduit mounting plates (ø 27, ø 33, ø 40). Select the mounting plate according to the diameter of the conduit used, and mount as shown in the figure below.

ø

27

mounting

ø

33

plate

ømounting

plate

40

Knock-

out

hole

If conduit is connected

from the bottom

ø

40

mounting

plate

ø

ø

27

33

mounting

mounting

If conduit is connected

plate

plate

from the front

Tapping screw

Unit front

4.Piping connection

Connect indoor unit crossover cables of the transmission cables ter- minal block (TB3) of the variable capacity unit to the transmission cables terminal block (TB3). When making an indoor/outdoor con- nection with shielded wiring, connect the shield ground to the earth screw ().

1 0 1

Address

CONT. board

Controlbox	Power	Earth screw	Transmission
	terminal block	(E)	cables terminal block
	(TB1)		(TB3)

c. Transmission booster (optional)

(For details, see item 11.3. “Wiring transmission cables”)

Connect 220/230/240 VAC to L/N of power terminal block (TB1). Connect the ground to the terminal of power terminal block (TB1).

Connect the outdoor unit side transmission cables to A/B of transmission cables terminal block 1 (TB2). Connect the outdoor unit side shield to S of transmission cables terminal block 1 (TB2).

Connect additional indoor unit side transmission cables to A/B of transmission cables terminal block 2 (TB3). Connect additional indoor unit side shield to S of transmission cables terminal block 2 (TB3).

Power terminal block (TB1)

Earth

T B 1

220V - 240V ~/N

L N

UP

TB 3	B S
	A
2	S
TB	B
	A

Transmission cables terminal block 2 (TB3)

Transmission cables terminal block 1 (TB2)

26

Image 26

Mitsubishi Electronics PUHY-YMC installation manual Plate, Hole, Transmission booster optional

Contents

PUHY-YMC Contents Before getting installed Safety precautionsBefore installation and electric work Before getting installed moved electrical work Before starting the test run Combination with indoor units Confirmation of parts attached Model Name Connecting pipe Elbow Shape Outdoor unit configurationSelection of installation site Variable capacity unit Constant capacity unit When there is an obstruction above the unit Individual installationWhen inlet air enters from right and left sides of unit Space required around unit Be very careful to carry product Lifting method and weight of productCollective installation and continu- ous installation Example of collective installation Installation of unitInstallation Location of anchor bolt 60/61 dB A-weighted Connecting direction for refrigerant pipingDown piping and down wiring precautions Noise level PUHY-400/500YMC Snow and seasonal windCountermeasure to seasonal wind PUHN-200/250YMC Never perform a pump down. This will damage the compressor Refrigerant piping installationAreas of caution Refrigerant piping system + α Multiple line/header Precautions concerning piping connection and valve operation For variable capacity unit Gas side Liquid side Oil balance side Figure shows valve fully open 100 to 1000 to Tightening angle standard Pipe diameter mm 50 to 57.5 / 500 to75 to 750 to 60 to Oil balance pipe connection method Distributor gas connection method Part could be damaged if not cooled sufficiently Restrictions on the posture for attaching joints How to install branch pipeJoint Gram below Evacuation Airtight test and evacuationAirtight test No heat insulation must be provided for electric wires Thermal insulation of refrigerant piping Penetrations Inner wall concealed Floor fireproofing Electrical work Constant capacity unit Control box and connecting posi- tion of wiringVariable capacity unit Hole For details, see item 11.3. Wiring transmission cablesPlate Transmission booster optional Wiring examples Wiring transmission cablesConnecting a transmission booster Name, code and possible unit connections One remote control unit for each indoor unit Wiring method, address settingRemote control RC terminal block TB6 Within Address Unit Remote control operation Same as above For details, see wire connection example C Unit Range Setting method Wiring LineSame group to the remote control RC terminal block TB6 Main remote controller Extended length and the length to the most remote unit Capability Number of connected indoor units that can be WiringBooster RP Wiring of main power supply and equipment capacity Checking before getting test run Operation procedureTest run Test run method How to cope with test run abnormality Abnormality Display at LED lighting blinking Remarks Flag Relay output 6603 Transmission error Transmission route Busy ErrorPower on Flag 8 always lights Coping with remote controller abnormality Following phenomena do not represent abnormality emergency NMK Nknk Nkok NKPK#$%&*+ Nkqk #$%&*+#,%&- ./0123145&6789#$%&=?@. !# Sknk Skok #$% +,-.Ü TK= Uknk Ukok Ukpk Ukqk Vkok NMK= Nmknk = NMKOK= $%&*+,-./01 #$%&*+QMã NMKPK=L NMKQK= Ãã ! k·ãLâÖJÅã #$%&#*#%+, -. !*# NMKRK= NMKSK= #$%& *+& 012345678 .#$%&*+,-./0 1$%#234 NNK= NNKNK= NNKOK= NNKPK= Rsrv #$% +,-./012 NRO #$% +,-./0/12`kQN =EqRF= !# $%&*+ NNKQK= Vwt NOKNK= NOKOK= NOKPK= EptNF EibaF NOKQK= Nokrk `ççäáåÖ EÉ~íáåÖ NMK Nknk Nkqk #$%&!*+ Sknk Skok TK= Ukok Ukpk Ukqk Vkok NMK= NMKOK= #$%&*+QMã NMKPK=L NMKQK= #$%&#*#%+, -. !*# NMKRK= NMKSK= #$%& *+& 012345678 .#$%&*+,-./0 1$%#234 NNK= NNKOK= NNKPK= #$% +,-./012 NRO #$#%&* +,-./0123456 =EqRF= !# $%&*+ NNKQK= NOK= NOKPK= EptNF EibaF NOKQK= Nokrk WT02922X02