Manuals / Monarch / Lawn and Garden / Lawn Mower

Monarch 9800 manual The high energy setting is lost when you turn

Models: 9800

1 64

Download 64 pages 51.61 Kb

Page 27

The high energy setting is lost when you turn

off the printer.

H i g h E n e r g y R i b b o n L i m i t a t i o n s

When using the high energy ribbon option:

uUse a print speed of 2.5IPS (inches per second).

uPrinthead warranty is reduced to 100,000 inches.

uSerial bar codes cannot be printed.

uDo not use peel mode.

uNo more than 20% of the supply should have print (black coverage).

CAUTION

The high energy ribbon may break or stick to the

supply when more than 20% of the supply

contains print.

uOnly white high energy supply should be used for bar code printing.

uReverse fonts cannot be used.

uA non-printing area of at least .1 inch (2.54 mm) must exist on the left and right edge of the ribbon.

uDo not print horizontal lines or bars.

uGraphics are limited.

Loading Ribbon 3-5

Image 27

Monarch 9800 manual The high energy setting is lost when you turn

Contents

Monarch 9800 Series Printers Trademarks CANADIAN D.O.C. WARNINGPage Page TA B L E O F C O N T E N T S iiTable of Contents G E T T I N G S TA R T E D A u d i e n c eU n p a c k i n g t h e P r i n t e r C o n n e c t i n g t h e P o w e r C a b l e 25 to 25 pin cable S e t t i n g D I P S w i t c h e s Verifier Lower DIP SwitchesDiagnostics Flow ControlP r i n t e r S t a t u s L i g h t s U s i n g t h e C o n t r o l P a n e lPause B u t t o n F u n c t i o n sS t a t u s C o d e B o Feed1-8 Getting Started High Energy L O A D I N G S U P P L I E SThermal Direct Thermal TransferL o a d i n g L a b e l s o r Ta g s Loading Supplies 2-4 Loading Supplies 11.Close the cover F o r P e e l M o d e Tear Edge Backing Paper 3.Feed the backing paper over the peel barLoading Supplies Peel Bar Lower OpeningU s i n g t h e O p t i o n a l Te a r B a r L O A D I N G R I B B O N L o a d i n g R i b b o n Take-upCore Take-upReel Ribbon Rollers Rev. A 10/98Loading Ribbon U s i n g a H i g h E n e r g y R i b b o n The high energy setting is lost when you turn 3-6 Loading Ribbon P R I N T I N G P r i n t i n gO n - D e m a n d M o d e P r i n t i n g C l e a r i n g B a t c h e s U s i n g B a t c h S e p a r a t o r sP r i n t i n g a n E r r o r L a b e l A d j u s t i n g P r i n t P o s i t i o n s Print Position Margin PositionCut Position Printing C l e a r i n g L a b e l J a m s C A R E A N D M A I N T E N A N C EC l e a n i n g 6.Clean the build-upin the supply path R e p l a c i n g t h e P r i n t h e a d 7.Carefully plug the cable into the new printhead 11.Let the printhead dry and reload your supplies A d j u s t i n g t h e P r i n t C o n t r a s t 4.Slide the fuse box back into the printer 1.Disconnect the printer from the power source5-8 Care and Maintenance R e p l a c i n g t h e F u s eP r i n t i n g a Te s t L a b e l T R O U B L E S H O O T I N GTr o u b l e s h o o t i n g D a t a E r r o r s E r r o r M e s s a g e s021Horizontal magnification must be 1 to 6-4 Troubleshooting014 Font selector is invalid 020Vertical magnification must be 1 to044 Dot pattern for line or box must be 104Batch mode must be N new or U updateTroubleshooting 041 Line direction must be 0, 90, 180, or209The incrementing amount must be 0 to 6-6 Troubleshooting207Incrementing start position must be 0 to 208Incrementing end position must be 0 to261Margin adjustment must be -99 to 99 dots 251Power up mode must be 0 online or 1 offline259Contrast adjustment must be -390 to 156 dots 260Print adjustment must be -99 to 99 dots287The printhead width is invalid 273Cut adjustment must be -300 to 300 dots6-8 Troubleshooting 286The buffer size is invalidC o m m u n i c a t i o n F a i l u r e s D a t a F o r m a t t i n g E r r o r s M a c h i n e F a u l t s 753Printer detected a sense mark that is too long 702Check your printer’s SETUP settings6-12 Troubleshooting 705Invalid batch received762Low battery. Recharge the battery Troubleshooting763Waiting to dispense label. Press Feed 6-14 Troubleshooting S P E C I F I C A T I O N S Ribbon Type R i b b o n S p e c i f i c a t i o nA c c e s s o r i e s Print SpeedSpecifications A-3 S E T T I N G D I P S W I T C H E S Stop Bits Upper DIP SwitchesBaud Rate Data BitsVerifier Lower DIP SwitchesDiagnostics Flow ControlB-4 Setting Dip Switches