Manuals / Monarch / Lawn and Garden / Lawn Mower

Monarch 9800 manual Let the printhead dry and reload your supplies

Models: 9800

1 64

Download 64 pages 51.61 Kb

Page 39

11.Let the printhead dry and reload your supplies.

Make sure the printhead cable does not touch the ribbon roll.

10.Clean the new printhead with a cotton swab dipped in isopropyl alcohol to remove any salt or oil left from handling.

11.Let the printhead dry and reload your supplies.

12.Close the printhead assembly and the cover. Turn on the printer.

13.Press Feed to position the supply under the printhead.

A d j u s t i n g t h e W i d e / N a r r o w K n o b s

You may need to adjust the two wide/narrow knobs according to the width of your supply. For supply that is more than two inches, adjust the knobs to the wide setting. For supply that is two inches or less, adjust the knobs to the narrow setting. For wide supplies, push down and turn the wide/narrow knobs clockwise with a screwdriver. For narrow supplies, turn the wide/narrow knobs counter-clockwise with a screwdriver until it pops back up.

You must adjust both of the knobs to the same position.

The adjustment is shown in the wide position.

5-6Care and Maintenance

Image 39

Monarch 9800 manual Let the printhead dry and reload your supplies

Contents

Monarch 9800 Series Printers Trademarks CANADIAN D.O.C. WARNINGPage Page TA B L E O F C O N T E N T S iiTable of Contents G E T T I N G S TA R T E D A u d i e n c eU n p a c k i n g t h e P r i n t e r C o n n e c t i n g t h e P o w e r C a b l e 25 to 25 pin cable S e t t i n g D I P S w i t c h e s Verifier Lower DIP SwitchesDiagnostics Flow ControlP r i n t e r S t a t u s L i g h t s U s i n g t h e C o n t r o l P a n e lPause B u t t o n F u n c t i o n sS t a t u s C o d e B o Feed1-8 Getting Started High Energy L O A D I N G S U P P L I E SThermal Direct Thermal TransferL o a d i n g L a b e l s o r Ta g s Loading Supplies 2-4 Loading Supplies 11.Close the cover F o r P e e l M o d e Tear Edge Backing Paper 3.Feed the backing paper over the peel barLoading Supplies Peel Bar Lower OpeningU s i n g t h e O p t i o n a l Te a r B a r L O A D I N G R I B B O N L o a d i n g R i b b o n Take-upCore Take-upReel Ribbon Rollers Rev. A 10/98Loading Ribbon U s i n g a H i g h E n e r g y R i b b o n The high energy setting is lost when you turn 3-6 Loading Ribbon P R I N T I N G P r i n t i n gO n - D e m a n d M o d e P r i n t i n g C l e a r i n g B a t c h e s U s i n g B a t c h S e p a r a t o r sP r i n t i n g a n E r r o r L a b e l A d j u s t i n g P r i n t P o s i t i o n s Print Position Margin PositionCut Position Printing C l e a r i n g L a b e l J a m s C A R E A N D M A I N T E N A N C EC l e a n i n g 6.Clean the build-upin the supply path R e p l a c i n g t h e P r i n t h e a d 7.Carefully plug the cable into the new printhead 11.Let the printhead dry and reload your supplies A d j u s t i n g t h e P r i n t C o n t r a s t 4.Slide the fuse box back into the printer 1.Disconnect the printer from the power source5-8 Care and Maintenance R e p l a c i n g t h e F u s eP r i n t i n g a Te s t L a b e l T R O U B L E S H O O T I N GTr o u b l e s h o o t i n g D a t a E r r o r s E r r o r M e s s a g e s021Horizontal magnification must be 1 to 6-4 Troubleshooting014 Font selector is invalid 020Vertical magnification must be 1 to044 Dot pattern for line or box must be 104Batch mode must be N new or U updateTroubleshooting 041 Line direction must be 0, 90, 180, or209The incrementing amount must be 0 to 6-6 Troubleshooting207Incrementing start position must be 0 to 208Incrementing end position must be 0 to261Margin adjustment must be -99 to 99 dots 251Power up mode must be 0 online or 1 offline259Contrast adjustment must be -390 to 156 dots 260Print adjustment must be -99 to 99 dots287The printhead width is invalid 273Cut adjustment must be -300 to 300 dots6-8 Troubleshooting 286The buffer size is invalidC o m m u n i c a t i o n F a i l u r e s D a t a F o r m a t t i n g E r r o r s M a c h i n e F a u l t s 753Printer detected a sense mark that is too long 702Check your printer’s SETUP settings6-12 Troubleshooting 705Invalid batch received762Low battery. Recharge the battery Troubleshooting763Waiting to dispense label. Press Feed 6-14 Troubleshooting S P E C I F I C A T I O N S Ribbon Type R i b b o n S p e c i f i c a t i o nA c c e s s o r i e s Print SpeedSpecifications A-3 S E T T I N G D I P S W I T C H E S Stop Bits Upper DIP SwitchesBaud Rate Data BitsVerifier Lower DIP SwitchesDiagnostics Flow ControlB-4 Setting Dip Switches