Motorola RVN4002K - page 37

F5 Print screen - This function key will print out everything shown on the screen.

F6 Copy all To all - This function key will copy EVERY alignment parameter in the current

channel to all the channels in the radio regardless of zone.

The lower portion of the screen contains some additional information that will be helpful in the

alignment process. The SQ field lets the user know whether or not squelch has been detected

by the radio's receiver. This allows you to set threshold squelch on those channels which are PL

protected. This means that you will not need to have any carrier squelch channels programmed

into the radio in order to set the squelch.

1. Squelch

When aligning squelch on PL/DPL channels, use the squelch (SQ) field in the lower portion

of the screen to determine when the radio squelches. On carrier squelch (CSQ) channels,

you can also listen to the reference speaker in the portable products test set. When aligning

Squelch, you can hear the change in the squelch level during the alignment process or in

"real time." You do not have to reprogram the radio to hear the immediate change.

(a) Follow the Setup Procedure in Section VI-A, Fig. 8.

(b) Select any channel on the radio.

(c) Select the SQUELCH function in the ALIGN CHANNEL screen.

(d) With no RF signal applied to the radio, set the squelch value to $0 by using the DOWN

arrow key. You should hear noise through the speaker in the test set (CSQ) and SQ

should be OFF (CSQ & PL/DPL). Set the switch on the test set at the load position

instead of the speaker position and the volume on the radio set at rated audio.

(e) Connect the RF BNC connector to the service monitor so that you can measure SINAD.

(f) Increase the RF, on the correct carrier frequency, until 8dB to 12dB SINAD is measured.

(g) Increment the squelch value by using the UP arrow key until the radio squelches (no

noise present or SQ is ON). The valid range for squelch is from $0 to $0F, with a default

value of $09.

(h) You can now set the same squelch value to all the channels in the radio by pressing the

F2 key. Pressing the F2 key will cause the current squelch value to be copied over to all

the other channels in the radio. If you want to make the squelch value different on any

other channel, you will have to go to that channel and set the squelch by following the

procedure given above.

Servicing the Radio 31

Contents

Main SABERTM Portable Radios FOREWORD COMPUTER SOFTWARE COPYRIGHTS TABLE OF CONTENTS inside front cover iv SABERTM Portable Radios R07.01.00 ii LIST OF FIGURES LIST OF TABLES ACRONYMS and ABBREVIATIONS iv I. INTRODUCTION A. About This Guide B. Functions Performed C. Customer Support II. GETTING STARTED A. How This Manual Is Organized B. How The Screens Are Organized Figure 1. Radio Service Software Program Tree 4 Getting Started Figure 1 C. How To Read The Screens Figure 2. Screen Display Format D. How To Use The Keyboard E. The MAIN Menu Figure 3. MAIN Menu Page III. HARDWARE INSTALLATION A. Host Computer And Options Required B. Optional Hardware Requirements C. Connecting The Radio To The Computer 512k RAM RIB DOS 3.1 Page IV. SOFTWARE INSTALLATION A. How To Install The Software Page Page B. How To Configure The Software For Your Computer 15Software Installation Figure 5. Setup Computer Configuration Figure 6. PC Configuration Figure 7. Configure Screen Colors Page V. THE HELP SCREEN VI. SERVICING THE RADIO A. How To Set Up Figure 8. Test Setup for Alignment Procedure Figure 9. Service/Alignment Menu 21Servicing the Radio B. Align Radio Parameters 22 Servicing the Radio after Figure 10a. Align Radio Menu 1 Figure 10b. Align Radio Menu 2 Page Page Page Page Page Page Page C. Align Channel Parameters Figure 11. Align Channel Menu Page Page D. Align Scan Controls Figure 12. Align Scan Menu Page Page Page VII. GET/SAVE/PROGRAM CODEPLUG DATA FROM/TO DISK/CODEPLUG Get/Save/Program Codeplug Data 37 Figure 13. Get/Save/Program Menu A. The READ function Figure 14. Read Radio Display B. The WRITE function Figure 15. Write Data to Radio Figure 16. Extraction of Radio Alignment Data C. The LOAD/SAVE/DELETE functions Figure 17. Save RPF Display Get/Save/Program Codeplug Data 43 VIII. CHANGE/CREATE/VIEW RADIO PERSONALITY Figure 18. Change/Create/View Codeplug Menu F2: VIEW Radio Personality Figure 19. VIEW Radio Personality Menu A. F3: CREATE Radio Personality File Figure 20. CREATE RPF Menu Page B. Radio Feature Options Figure 21. Options Screen 48 Change/Create/View Radio Personality Page Page Figure 22. Quik- Call II System Selection Screen Figure 23. Quik- Call II H701 Parameters Screen Figure 24. Quik- Call II H702 Parameters Screen 52 Change/Create/View Radio Personality Figure 25. Quik- Call II H703 Parameters Screen Figure 26. Multiple Repeater Access Codes Screen Change/Create/View Radio Personality 53 C. Channel Information Figure 27. Channel Information Screen Page Page Page Figure 28. Wide View Screen Page D. Auto Dial / Access and Hangup Codes Figure 29. Autodial Setup Screen E. Manual Interconnect Access and Hangup Codes Figure 30. Manual Telephone Interconnect Screen F. Format Scan Lists Figure 31. Create/Modify Scan Lists Screen Page G. Format Selectable PL Figure 32. Create/Modify Selectable PL Codes IX. PRINT RADIO PERSONALITY Change/Create/View Radio Personality 65 Figure 33. Print Menu Page APPENDIX - 1. ERROR MESSAGES Page APPENDIX - 2. KEYBOARD COMMANDS APPENDIX - 3. How To Format A Disk A. Dual-Floppy Disk Drive Systems B. Hard Disk Systems APPENDIX - 4. SABER Models APPENDIX - 5. Options List and Definitions Page Page Page 2nd Fixed Priority Nuisance Mode Delete Scroll Scan List Designated Transmit Mode Priority to Follow Channel Selector Switch Mode Slaved Scan Autoscan Page Page Page Page Radio Check Radio Inhibit Page Page APPENDIX - 6. Quik-Call II Frequencies and Codes Table 1: Motorola System Table 2: General Electric System Table 3: Plectron System Table 4: Federal System APPENDIX - 7. SQUELCH CODES Appendix - 7. Squelch Codes 89 PRIVATE LINE (PL) CODES AND THEIR CORRESPONDING FREQUENCIES (in Hz) DIGITAL PRIVATE LINE (DPL) CODES GLOSSARY Page Page Page Page Page INDEX