Motorola RVN4002K - page 61

All keyboard commands can be found in Section II-D. with specific keyboard functions

explained below:

UP/DN arrow keys will scroll through each channel.

PGUP/PGDN keys will scroll through each zone.

RIGHT/LEFT arrow keys will move cursor within an entry.

CTRL END will clear to end of the field.

Valid entries for Transmit/Receive frequencies (TX/RX FREQ), Power Level,

Transmit/Receive PL codes (TX/RX PL),and Scan list are listed below:

Data Field Allowed Entries

TX /RX FREQ Minimum and maximum values are dependent on the

frequency range you had selected in the CREATE RPF

screen. Try to enter frequencies in either 6.25 or 5 kHz steps

or a 'B' for BLANK in the TX Freq field for a RECEIVE-only

channel.

Power Select one of four power levels: (L)ow, (M)edium, (H)igh, or

(S)pecial. The power level for this channel will correspond to

the power level by the same name inthe"Align Radio Para-

meters" Screen.

TX/RX PL For Carrier Squelch, enter either CSQ or "Spaces"." For

Tone PL codes, enter either the frequency in Hertz as XXX.X

or as a two digit alpha code. For Digital PL codes, enter the

three digit DPL code word (Note: no decimal places may be

entered for DPL). RX PL and Quik- Call II are incompatible

on a channel. See Appendix 7 for a complete list of squelch

codes.

Scan List Valid entries range from 1 - 10.

Time Out Timer Valid entries are 'Y' and 'N'. This field will be displayed if

H251/H901 is selected. If 'Y' is entered, the time out timer

valu the radio option screen will be used to limit the length of

tansmission. If 'N' is entered, the length of transmission is

unlimited.

MDC ID on PTT Valid entries are 'Y' and 'N'. This field will be displayed if

H958/H959/H961/H962/H963/H967/H923/H946 is selected.

If 'Y' is entered, the MDC ID will be sent out preceding all

transmissions on this channel.

Emergency Revert Valid entries are 'Y' and 'N'. This field will be displayed if

H961/H962/H963/H967/H923/H946 is selected. This field

determines the Emergency capability for this channel.

Enable XL Valid entries are 'Y' and 'N'. This field will be displayed for

Secure model radios.

Channel Strapping Possible entries are c (for clear), s (for secure), and blank (to

follow switch

Change/Create/View Radio Personality 55

Contents

Main SABERTM Portable Radios FOREWORD COMPUTER SOFTWARE COPYRIGHTS TABLE OF CONTENTS inside front cover iv SABERTM Portable Radios R07.01.00 ii LIST OF FIGURES LIST OF TABLES ACRONYMS and ABBREVIATIONS iv I. INTRODUCTION A. About This Guide B. Functions Performed C. Customer Support II. GETTING STARTED A. How This Manual Is Organized B. How The Screens Are Organized Figure 1. Radio Service Software Program Tree 4 Getting Started Figure 1 C. How To Read The Screens Figure 2. Screen Display Format D. How To Use The Keyboard E. The MAIN Menu Figure 3. MAIN Menu Page III. HARDWARE INSTALLATION A. Host Computer And Options Required B. Optional Hardware Requirements C. Connecting The Radio To The Computer 512k RAM RIB DOS 3.1 Page IV. SOFTWARE INSTALLATION A. How To Install The Software Page Page B. How To Configure The Software For Your Computer 15Software Installation Figure 5. Setup Computer Configuration Figure 6. PC Configuration Figure 7. Configure Screen Colors Page V. THE HELP SCREEN VI. SERVICING THE RADIO A. How To Set Up Figure 8. Test Setup for Alignment Procedure Figure 9. Service/Alignment Menu 21Servicing the Radio B. Align Radio Parameters 22 Servicing the Radio after Figure 10a. Align Radio Menu 1 Figure 10b. Align Radio Menu 2 Page Page Page Page Page Page Page C. Align Channel Parameters Figure 11. Align Channel Menu Page Page D. Align Scan Controls Figure 12. Align Scan Menu Page Page Page VII. GET/SAVE/PROGRAM CODEPLUG DATA FROM/TO DISK/CODEPLUG Get/Save/Program Codeplug Data 37 Figure 13. Get/Save/Program Menu A. The READ function Figure 14. Read Radio Display B. The WRITE function Figure 15. Write Data to Radio Figure 16. Extraction of Radio Alignment Data C. The LOAD/SAVE/DELETE functions Figure 17. Save RPF Display Get/Save/Program Codeplug Data 43 VIII. CHANGE/CREATE/VIEW RADIO PERSONALITY Figure 18. Change/Create/View Codeplug Menu F2: VIEW Radio Personality Figure 19. VIEW Radio Personality Menu A. F3: CREATE Radio Personality File Figure 20. CREATE RPF Menu Page B. Radio Feature Options Figure 21. Options Screen 48 Change/Create/View Radio Personality Page Page Figure 22. Quik- Call II System Selection Screen Figure 23. Quik- Call II H701 Parameters Screen Figure 24. Quik- Call II H702 Parameters Screen 52 Change/Create/View Radio Personality Figure 25. Quik- Call II H703 Parameters Screen Figure 26. Multiple Repeater Access Codes Screen Change/Create/View Radio Personality 53 C. Channel Information Figure 27. Channel Information Screen Page Page Page Figure 28. Wide View Screen Page D. Auto Dial / Access and Hangup Codes Figure 29. Autodial Setup Screen E. Manual Interconnect Access and Hangup Codes Figure 30. Manual Telephone Interconnect Screen F. Format Scan Lists Figure 31. Create/Modify Scan Lists Screen Page G. Format Selectable PL Figure 32. Create/Modify Selectable PL Codes IX. PRINT RADIO PERSONALITY Change/Create/View Radio Personality 65 Figure 33. Print Menu Page APPENDIX - 1. ERROR MESSAGES Page APPENDIX - 2. KEYBOARD COMMANDS APPENDIX - 3. How To Format A Disk A. Dual-Floppy Disk Drive Systems B. Hard Disk Systems APPENDIX - 4. SABER Models APPENDIX - 5. Options List and Definitions Page Page Page 2nd Fixed Priority Nuisance Mode Delete Scroll Scan List Designated Transmit Mode Priority to Follow Channel Selector Switch Mode Slaved Scan Autoscan Page Page Page Page Radio Check Radio Inhibit Page Page APPENDIX - 6. Quik-Call II Frequencies and Codes Table 1: Motorola System Table 2: General Electric System Table 3: Plectron System Table 4: Federal System APPENDIX - 7. SQUELCH CODES Appendix - 7. Squelch Codes 89 PRIVATE LINE (PL) CODES AND THEIR CORRESPONDING FREQUENCIES (in Hz) DIGITAL PRIVATE LINE (DPL) CODES GLOSSARY Page Page Page Page Page INDEX