Motorola RVN4002K A. The READ function

A. The READ function

The READ function will read the radio codeplug data from the radio and generate an RSS

PC file. In order to read the codeplug, you need to connect the radio to the system. To read

the radio, follow the setup procedure shown in Figure 4.

• Make sure the radio is not in scan mode.

• Regardless of the type of radio model being read back (whether a SABER I, II, or III), the

programmer will always read the contents of the CORE processor first. The system will

display the software version level of the CORE processor being read,for example:

CORE 5d , or 6d, etc...

• After reading the CORE, the system will read the COPE processor followed by the

contents of the external EEPROM. This process will only occur on SABER II and III

models.

• After the contents of the radio have been read back, the system will convert this data into

the radio personality file. As the system is building the RPF, several messages will

appear on the screen showing the process of the "build." Shown below in Figure 14 is

a sample screen of READ radio.

Figure 14. Read Radio Display

Note: Before reading the radio, a message may appear instructing you to press the three top

keys down on the keypad (for a SABER II and III) simultaneously and turn the radio off and

back on to get an ERR X YZ message on the display. Don't worry about the message unless

the READ radio function does not execute. If the error message does not disappear or the

READ function locks up, refer to Appendix-1, "ERROR MESSAGES."

Get/Save/Program Codeplug Data38

F1

F4

F2

F3

F5

F6

F7

F8

F9

F10

MOTOROLA Radio Service Software

SABER Model:

Ver. R05.00.00

Main.Get/Save/Prog.Read/Prog. Read

READ DATA FROM A RADIO

Accessing Serial Bus.

0% 100%

................................................

................................................

................................................

Reading CORE 6D

Reading COPE internal

Reading COPE external

R07.01.00

100%

Contents

Main SABERTM Portable Radios FOREWORD COMPUTER SOFTWARE COPYRIGHTS TABLE OF CONTENTS inside front cover iv SABERTM Portable Radios R07.01.00 ii LIST OF FIGURES LIST OF TABLES ACRONYMS and ABBREVIATIONS iv I. INTRODUCTION A. About This Guide B. Functions Performed C. Customer Support II. GETTING STARTED A. How This Manual Is Organized B. How The Screens Are Organized Figure 1. Radio Service Software Program Tree 4 Getting Started Figure 1 C. How To Read The Screens Figure 2. Screen Display Format D. How To Use The Keyboard E. The MAIN Menu Figure 3. MAIN Menu Page III. HARDWARE INSTALLATION A. Host Computer And Options Required B. Optional Hardware Requirements C. Connecting The Radio To The Computer 512k RAM RIB DOS 3.1 Page IV. SOFTWARE INSTALLATION A. How To Install The Software Page Page B. How To Configure The Software For Your Computer 15Software Installation Figure 5. Setup Computer Configuration Figure 6. PC Configuration Figure 7. Configure Screen Colors Page V. THE HELP SCREEN VI. SERVICING THE RADIO A. How To Set Up Figure 8. Test Setup for Alignment Procedure Figure 9. Service/Alignment Menu 21Servicing the Radio B. Align Radio Parameters 22 Servicing the Radio after Figure 10a. Align Radio Menu 1 Figure 10b. Align Radio Menu 2 Page Page Page Page Page Page Page C. Align Channel Parameters Figure 11. Align Channel Menu Page Page D. Align Scan Controls Figure 12. Align Scan Menu Page Page Page VII. GET/SAVE/PROGRAM CODEPLUG DATA FROM/TO DISK/CODEPLUG Get/Save/Program Codeplug Data 37 Figure 13. Get/Save/Program Menu A. The READ function Figure 14. Read Radio Display B. The WRITE function Figure 15. Write Data to Radio Figure 16. Extraction of Radio Alignment Data C. The LOAD/SAVE/DELETE functions Figure 17. Save RPF Display Get/Save/Program Codeplug Data 43 VIII. CHANGE/CREATE/VIEW RADIO PERSONALITY Figure 18. Change/Create/View Codeplug Menu F2: VIEW Radio Personality Figure 19. VIEW Radio Personality Menu A. F3: CREATE Radio Personality File Figure 20. CREATE RPF Menu Page B. Radio Feature Options Figure 21. Options Screen 48 Change/Create/View Radio Personality Page Page Figure 22. Quik- Call II System Selection Screen Figure 23. Quik- Call II H701 Parameters Screen Figure 24. Quik- Call II H702 Parameters Screen 52 Change/Create/View Radio Personality Figure 25. Quik- Call II H703 Parameters Screen Figure 26. Multiple Repeater Access Codes Screen Change/Create/View Radio Personality 53 C. Channel Information Figure 27. Channel Information Screen Page Page Page Figure 28. Wide View Screen Page D. Auto Dial / Access and Hangup Codes Figure 29. Autodial Setup Screen E. Manual Interconnect Access and Hangup Codes Figure 30. Manual Telephone Interconnect Screen F. Format Scan Lists Figure 31. Create/Modify Scan Lists Screen Page G. Format Selectable PL Figure 32. Create/Modify Selectable PL Codes IX. PRINT RADIO PERSONALITY Change/Create/View Radio Personality 65 Figure 33. Print Menu Page APPENDIX - 1. ERROR MESSAGES Page APPENDIX - 2. KEYBOARD COMMANDS APPENDIX - 3. How To Format A Disk A. Dual-Floppy Disk Drive Systems B. Hard Disk Systems APPENDIX - 4. SABER Models APPENDIX - 5. Options List and Definitions Page Page Page 2nd Fixed Priority Nuisance Mode Delete Scroll Scan List Designated Transmit Mode Priority to Follow Channel Selector Switch Mode Slaved Scan Autoscan Page Page Page Page Radio Check Radio Inhibit Page Page APPENDIX - 6. Quik-Call II Frequencies and Codes Table 1: Motorola System Table 2: General Electric System Table 3: Plectron System Table 4: Federal System APPENDIX - 7. SQUELCH CODES Appendix - 7. Squelch Codes 89 PRIVATE LINE (PL) CODES AND THEIR CORRESPONDING FREQUENCIES (in Hz) DIGITAL PRIVATE LINE (DPL) CODES GLOSSARY Page Page Page Page Page INDEX