A

B

C

D

During installation of the sealing plate, its underside must first be inserted behind the raised edge so that a good seal is achieved.

MTD-ERV 350 – L

Pull the tape (E) to remove the heat ex- changer (F) and the drain plate (G).

Remove the bypass duct (H) on the left-hand version of the MTD-ERV 350.

MTD-ERV 350 – R

Remove the bypass duct (H) on the right-hand version of the MTD-ERV 350.

Pull the tape (E) to remove the heat exchanger

(F) and the drain plate (G).

Designated as L

G

E

B

F

Left-hand version

4

Designated as R

E

G

F

Right-hand version

Then:

Remove the heat exchanger (F) from the drain plate (G).

Caution!

There may still be water in the heat ex- changer!

Clean the heat exchanger (F), if necessary.

Immerse the heat exchanger in warm wa- ter (max. 40° C) to clean.

Finally rinse the heat exchanger thorough- ly with warm tap water (max. 40° C).

Hold the heat exchanger with both hands at the green side surfaces and shake out all the water.

Caution!

On no account should aggressive or sol- vent-based cleaning agents be used.

Do not install the heat exchanger yet (the fans can be removed, inspected and cleaned, if necessary, in the following steps).

If an enthalpy heat exchanger is in- stalled, observe the corresponding in- struction.

Do not install the heat exchanger yet if the fans are also to be inspected. The following section describes how to remove, inspect and clean the fans, if necessary, after the heat exchanger:

Remove the plastic plate (I) in front of the PCB panel by loosening the two screws.

Loosen the connectors (J) and the earth cable

(J)atthePCBpanelandremovethecableswith the two grommets (K) completely.

Removethecompletefancasing(L)bypressing in the tabs (M).

Remove the inlet neck (N) by pressing in the tabs around the fan casing.

Clean the fans (O).

Instructions for the Installer 35

Page 39
Image 39
MTD ERV 365 manual MTD-ERV 350 L, MTD-ERV 350 R

ERV 350, ERV 365 specifications

The MTD ERV 365 and ERV 350 are advanced energy recovery ventilation (ERV) systems designed to enhance indoor air quality and energy efficiency in residential and commercial buildings. These units utilize cutting-edge technologies to transfer heat and moisture between incoming and outgoing air streams, optimizing the temperature and humidity levels of the conditioned air.

One of the main features of the MTD ERV 365 is its high energy recovery efficiency. Equipped with a specially designed heat exchanger, this ERV can reclaim a significant portion of the energy from the exhaust air, reducing the heating and cooling load on HVAC systems. This results in lower energy bills and decreased environmental impact. The ERV 350 offers similar benefits but is tailored for slightly smaller spaces, making it suitable for various residential applications.

Both models are constructed with durability in mind, featuring robust housing and weather-resistant materials that ensure long-lasting performance. The MTD ERV series is designed to withstand varying environmental conditions, ensuring reliable operation in challenging climates. Additionally, noise-reduction technology minimizes operational sounds, promoting a peaceful indoor environment.

User-friendly controls are another highlight of the MTD ERV systems. They come equipped with intuitive interfaces, allowing users to easily adjust settings, monitor performance, and receive maintenance notifications. Advanced sensors provide real-time data on indoor air quality parameters, ensuring optimal operation based on the specific needs of the environment.

Installation and maintenance are made straightforward with these ERV units. They feature a compact design that facilitates integration into existing HVAC systems or new constructions. Filters are easily accessible for routine cleaning or replacement, maintaining peak performance over time.

Furthermore, both the MTD ERV 365 and ERV 350 are designed with sustainability in mind. Using materials that are recyclable and energy-efficient components contributes to a reduced carbon footprint. These ERV systems also comply with various building codes and standards, ensuring they meet industry requirements for safety and efficiency.

In summary, the MTD ERV 365 and ERV 350 are sophisticated energy recovery ventilation solutions that combine advanced technologies and user-friendly features. With high energy recovery efficiency, durable construction, and easy integration, they stand out as models for improving indoor air quality and energy efficiency in a variety of settings.