Multi-Tech Systems MT5634SMI V.92, MT5634SMI V.34 manual 134, +FTH Transmit Data with Hdlc Framing

Index

AT Command Implementation	49
AT Command Mode	50
Fax Class 2 Parameter Table	54
Fax Commands
+FAA – Auto Answer Enable Class 1.0	37
+FAE – Auto Answer Enable Clas 1 & 1.0	37
+FAR – Adaptive Reception Control	41
+FCL – Carrier Loss Timeout	41
+FCLASS=1 – Select Facsimile Class 1 Mode	37
+FCLASS=1.0 – Select Facsimile Class 1.0 Mode	37
+FDD – Double Escape Character Replacement	42
+FIT – DTE Inactivity Timeout	42
+FLO – Flow Control	44
+FMI? – Request Manufacturer Identification	43
+FMM? – Request Model Identification	43
+FMR? – Request Revision Identification	43
+FPR – Fixed DTE Rate	43
+FRH – Receive Data With HDLC Framing	40
+FRM – Receive Facsimile	39
+FTH – Transmit Data with HDLC Framing	40
+FTM – Transmit Facsimile	38
+FTS – Receive Silence	38
+FTS – Transmit Silence	37
Fax Connection Response - +FCO	64
fax control reception	35
fax control transmission	34
fax data reception	36
fax data transmission	36
Fax double escape character replacement
- +FDD	42
Fax DTE inactivity timeout parameter - +FIT	42
Fax fixed DTE rate parameter - +FPR	43
Fax Flow Control - +FLO	90
Fax flow control parameter - +FLO	44
fax I/O processing	33
fax origination	34
Fax receive data with HDLC framing command - +FRH .40
Fax Receive Facsimile - +FRM	39
Fax Receive Silence - +FRS	38
fax request manufacturer identification parameter - +FMI?
......................................................................................	43
Fax request model identification parameter - +FMM?	43
Fax request revision identification parameter - +FMR?....43
Fax Service Class 2 and Service Class 2.0/2.1	48
Fax Transmit Data with HDLC Framing - +FTH	40
Fax Transmit Facsimile - +FTM	38
Fax transmit silence command - +FTS	37
Firmware Version, Displaying	10
flash	24
Flow control	15
Flow Control	121
Flow Control Selection command - &K	12
Flow Control Selection command - \Q	15
frame information	65
G
Global Wizard	130
Guard Tone Control command	12
H
Handshake	10
Hangup command	9
Hook Control command - H	9
Hose Phase C Response Time Out - +FPHCTO	85
Host Phase C Response Timeoout	85

I
identification commands	59
Identify Analog Source/Destination Configuration and
Event Reporting Capabilities command +VLS=?	112
Inactivity timer - S30	28
Inactivity Timer command - \T	15
Indicate Document to Poll - +FLP	78
Information Request command - I	10
Initialization strings	5
Initialize Fax Parameters	63
Initialize Fax Parameters - +FIP	63
Initialize Voice Parameters command - VIP	107
Interface Configuration commands
+VBT= - Modem Flow Control Assert & Deassert ...	119
+VBT=? – Report Modem Flow Control	119
+VPP= - Enable/Disable Voice Mode	119
+VPR= - Select DTE/DCE Interface Rate	120
Interface Configuration Commands	119
L
Leased Line Operation command - &L	13
Line feed character - S4	28
Load Factory Settings command - &F	12
Local Callback Inactivity Timer command - #CBI	26
Local Callback Inactivity Timer command #CBI – Local
Callback Inactivity Timer	19
Local ID String - +FLI	77
Local Polling ID String	77
Local Polling ID String - +FPI	77
Loopback Test commands - &T	13
M
Mandatory Parameter Commands	57
Minimum Phase C Speed - +FMS	86
miscellaneous parameters	92
MNP 5 data compression	16
MNP Error Correction	15
Modem Capabilities Parameters - +FCC	72
Modem on Hold	24
Modem on Hold Enable command - +PMH=	23
Modem on Hold Initiate command - +PMHR=	24
Modem on Hold Timer command - +PMHT=	24
Modem Reset command - Z	11
Modes of Interaction	50
Modulation Handshake command N	10
Modulation Selection command - +MS=	22
Monitor Speaker Mode command - M	10
N
Negotiation Reporting - +FNR	80
Non-standard Frame FIF String - +FNS	78
Numeric Parameters	51
O
On-hook/off-hook	9
Online BPS Speed command - $MB	17
Online command mode	5
Optional Parameter Commands	58
Originate a Call - D	61
P
Page Header Generation	91

Multi-Tech Systems, Inc. SocketModem MT5634SMIxx Reference Guide (S000263C) 134