Remote Configuration | Multi-Tech Systems MT5634ZPX-PCI manual

Owner’s Manual

9.If you are required to dial 9 to get an outside line, edit the dialing prefix to include a 9 and a comma, e.g., ATDT9, (the comma inserts a pause before dialing the next digit).

Similarly, to turn off call waiting for the duration of the call, insert the disabling code used in your area, e.g., ATDT*70,. If you are using Windows 95-compliant software, make these changes in the How I dial from this location box of Dialing Properties.

Note: *70 is used only in the United States.

Remote Configuration

Remote configuration is a network management tool that allows you to configure modems anywhere in your network from one location. With password-protected remote configuration, you can issue AT commands to a remote MT5634ZPX-PCI modem for maintenance or troubleshooting as if you were on-site.

Basic Procedure

Use these steps for connections established by the local or by the remoteMulti-Tech modem.

1.Establish a data connection with a remote MT5634ZPX-PCI modem.

2.Send three remote configuration escape characters followed by AT and the setup password. Then press ENTER. Example:

%%%ATMTSMODEM<cr>. You have four attempts to enter the password correctly before being disconnected. If the password is correct, the remote modem responds with OK.

3.You now can send AT commands to configure the remote modem.

4.When you finish configuring the remote modem, save the new configuration by typing AT&W0<cr>. Then type ATO<cr> to exit remote configuration. You can then break the connection in the normal way.

CAUTION: Hanging up while you are in remote configuration mode can lock up the remote modem.

30	MT5634ZPX-PCI

Image 30

Multi-Tech Systems MT5634ZPX-PCI owner manual Remote Configuration, Basic Procedure

Contents

Model MT5634ZPX-PCI MT5634ZPX -PCI Record of Revisions Contents Data is being lost Introduction Initial Checklist Common ProblemsIntroduction Limited Warranty Technical Support Introduction and Description MT5634ZPX-PCI Features Introduction and Description Peripiheral Component Interconnect PCI Fax Upstream Data Rates Support/FunctionsDownstream Rates Optional V.8bis Sequence What is in Your Modem Package? Digital Loss and Robbed-bit Signaling Auto Adapt How to Use This Manual Appendix Typographic Conventions You type this Installation Introduction What You’ll Need Safety Warnings Installation OverviewInstallation Configuring the MultiModem ZPX-PCI Windows 95 Plug and Play Installing the MultiModemZPX-PCI External Connections Plug the telephone’s line cable intoWith the modem, insert the microphone Installing Drivers Verifying Configuration Port COM Interrupt Address Speed Select Start, Settings, and then Control Panel Is Your MultiModemZPX-PCI Ready for Use?To Remove Previous Modem from Windows Operating Your MultiModemZPX-PCI Simple Operation Software Configuration Testing Data FunctionsSelect Start, Programs, Accessories, and then HyperTerminal Connect dialog box, click Dialing Properties Testing FAX Functions Click Start, Programs, Accessories, and then WordPadMultiModemZPX-PCI’s fax capabilities Testing Voice Function Click Start, Programs, Accessories, and then HyperTerminal MultiModemZPX-PCI’s Speakerphone Test AT+FCLASS=8 AT+VLS=7 Configuring Communications Software Installation Remote Configuration Basic Procedure Setup Changing the Setup Password PKUNZIP.EXE AT Commands, S-Registers, and Result Codes AT Commands Carrier Control AT Commands, Result Codes, and S-RegistersCommunication Standard Setting Dial Echo Online Data Characters Echo Command Mode CharactersDS=n Dial Stored Telephone Number Hook Control Return Online to Data Mode Monitor Speaker VolumeMonitor Speaker Mode Modulation Handshake Result Code Format Sr=n Set Register ValueSr? Read Register Value Result Code Selection Auto Retrain Modem ResetLong Space Disconnect Data Carrier Detect DCD Control Asynchronous Communications Mode Fn Load Factory Default SettingsCommunications Mode 22bis Guard Tone Control Store Current Configuration Self-Test CommandsView Current Configuration Select Stored Configuration for Hard Reset \Jn Data Buffer Control \Nn Error Correction Mode Selection\Gn Modem Port Flow Control \Kn Set Break Control \X n XON/XOFF Pass-Through \T n Inactivity Timer\V n Protocol Result Code Data Calling Tone Enable Synchronous Buffered Mode Allowed valueSpeaker Codec Loopback Registers Tones Decimal Disables, 1-255 enables Modulation50-150 Minute 255 Data mode Connect. Where K56flex provided=V.90/56Kflex disabled = disable 1 = enable S36=5,7 LAPM, MNP, or Async MNP or Async 1-4 sets the value toSets one of three 56K operating Result Codes Connected at 50000 bps Connected at 46000 bpsConnected at 48000 bps Connected at 52000 bps Troubleshooting Initial Checklist Common Problems Troubleshooting MT5634ZPX-PCI Modem dials but cannot make a connection Modem disconnects while online Modem cannot connect when answering Data is being lost Warranty, Service, and Tech Support/BBS Limited Warranty Online Warranty Registration Warranty, Service, and Tech Support Technical Support Recording Modem Information Service Multi-Tech Systems, Inc Woodale Drive Mounds View, MN To Download a file Multi-Tech BBSTo log on to the Multi-Tech BBS If you know the file name If you don’t know the file name About the Multi-Tech Fax-Back Service About CompuServeAbout the Internet Appendix Appendix a Regulatory Compliance FCC Regulations for Telephone Line Interconnection Fax Branding Statement AppendixMulti-Tech Systems, Inc Canadian Limitations Notice Appendix Product Safety Compliance +12 VDC, -12 VDC, +5 VDC Figure A-1. Creepage and Clearance Distances EMC, Safety and Terminal Directive Compliance European Low Voltage Directive New Zealand Modem Warning Notice 90/K56flex, ITU V.34 extended, V.34, ITU Appendix B Technical Specifications14,400, 12,000, 9600, 7200, 4800, 2400, ITU Group 3, T.4, T.30, V.21, V.27ter Appendix Fax Carrier Frequencies Hz mark, 1850 Hz space for Transmit Connectors Appendix C Ascii Conversion Chart Code HEX DEC Appendix D FLASHWINFlash Upgrade Introduction MT5634ZPX-PCI Index BBS Auto Retrain Enable/disable V25 data calling tone S35Index Data Fax-back service , 66 FCC Regulations , 68-81 firmware Fall-forward , 7 fallback , 7, 37 fax Tones dialing MT5634ZPX-PCI