Sr=n Set Register Value | Multi-Tech Systems MT5634ZPX-PCI specs

Owner’s Manual

Command:	Qn	Result Codes Enable/Disable
Values:		n = 0 or 1
Default:		0
Description:	Q0	Enable result codes.
	Q1	Disable result codes.

Command:	Sr=n Set Register Value
Values:	r = S-register number; n varies
Default:	None
Description:	Set value of register Sr to value of n, where n is entered in
	decimal format.

Command:	Sr?	Read Register Value
Values:		r = S-register number
Default:		None
Description:		Read value of register Sr and display value in 3-digit
		decimal form.

Command:	Vn	Result Code Format
Values:		n = 0 or 1
Default:		1
Description:	V0	Displays result codes as digits (terse response).
	V1	Displays result codes as words (verbose response).

Command:	Xn	Result Code Selection
Values:		n = 0–7
Default:		4
Description:	X0	Basic result codes (e.g., CONNECT); does not look for dial
		tone or busy signal.
	X1	Extended result codes (CONNECT 56000 V42bis,
		CONNECT 33600 V42bis, etc.); does not look for dial tone
		or busy signal.
	X2	Extended result codes with NO DIALTONE; does not look
		for busy signal.
	X3	Extended result codes with BUSY; does not look for dial
		tone.
	X4	Extended result codes with NO DIALTONE and BUSY.
	X5	Extended result codes with NO DIALTONE and BUSY.
	X6	Extended result codes with NO DIALTONE and BUSY.
	X7	Basic result codes with NO DIALTONE and BUSY.

38	MT5634ZPX-PCI

Image 38

Multi-Tech Systems MT5634ZPX-PCI owner manual Sr=n Set Register Value, Sr? Read Register Value, Result Code Format

Contents

Model MT5634ZPX-PCI MT5634ZPX -PCI Record of Revisions Contents Data is being lost Introduction Initial Checklist Common ProblemsIntroduction Limited Warranty Technical Support Introduction and Description MT5634ZPX-PCI Features Introduction and Description Peripiheral Component Interconnect PCI Fax Upstream Data Rates Support/FunctionsDownstream Rates Optional V.8bis Sequence What is in Your Modem Package? Digital Loss and Robbed-bit Signaling Auto Adapt How to Use This Manual Appendix Typographic Conventions You type this Installation Introduction What You’ll Need Installation Safety WarningsInstallation Overview Configuring the MultiModem ZPX-PCI Windows 95 Plug and Play Installing the MultiModemZPX-PCI With the modem, insert the microphone External ConnectionsPlug the telephone’s line cable into Installing Drivers Verifying Configuration Port COM Interrupt Address Speed To Remove Previous Modem from Windows Select Start, Settings, and then Control PanelIs Your MultiModemZPX-PCI Ready for Use? Operating Your MultiModemZPX-PCI Simple Operation Select Start, Programs, Accessories, and then HyperTerminal Software ConfigurationTesting Data Functions Connect dialog box, click Dialing Properties MultiModemZPX-PCI’s fax capabilities Testing FAX FunctionsClick Start, Programs, Accessories, and then WordPad Testing Voice Function Click Start, Programs, Accessories, and then HyperTerminal MultiModemZPX-PCI’s Speakerphone Test AT+FCLASS=8 AT+VLS=7 Configuring Communications Software Installation Remote Configuration Basic Procedure Setup Changing the Setup Password PKUNZIP.EXE AT Commands, S-Registers, and Result Codes AT Commands Carrier Control AT Commands, Result Codes, and S-RegistersCommunication Standard Setting Dial Echo Online Data Characters Echo Command Mode CharactersDS=n Dial Stored Telephone Number Hook Control Return Online to Data Mode Monitor Speaker VolumeMonitor Speaker Mode Modulation Handshake Result Code Format Sr=n Set Register ValueSr? Read Register Value Result Code Selection Auto Retrain Modem ResetLong Space Disconnect Data Carrier Detect DCD Control Asynchronous Communications Mode Fn Load Factory Default SettingsCommunications Mode 22bis Guard Tone Control Store Current Configuration Self-Test CommandsView Current Configuration Select Stored Configuration for Hard Reset \Jn Data Buffer Control \Nn Error Correction Mode Selection\Gn Modem Port Flow Control \Kn Set Break Control \X n XON/XOFF Pass-Through \T n Inactivity Timer\V n Protocol Result Code Data Calling Tone Speaker Codec Loopback Enable Synchronous Buffered ModeAllowed value Registers Tones Decimal Disables, 1-255 enables Modulation50-150 Minute 255 Data mode Connect. Where K56flex provided=V.90/56Kflex disabled = disable 1 = enable Sets one of three 56K operating S36=5,7 LAPM, MNP, or Async MNP or Async1-4 sets the value to Result Codes Connected at 50000 bps Connected at 46000 bpsConnected at 48000 bps Connected at 52000 bps Troubleshooting Initial Checklist Common Problems Troubleshooting MT5634ZPX-PCI Modem dials but cannot make a connection Modem disconnects while online Modem cannot connect when answering Data is being lost Warranty, Service, and Tech Support/BBS Limited Warranty Online Warranty Registration Warranty, Service, and Tech Support Technical Support Recording Modem Information Service Multi-Tech Systems, Inc Woodale Drive Mounds View, MN To Download a file Multi-Tech BBSTo log on to the Multi-Tech BBS If you know the file name If you don’t know the file name About the Internet About the Multi-Tech Fax-Back ServiceAbout CompuServe Appendix Appendix a Regulatory Compliance FCC Regulations for Telephone Line Interconnection Multi-Tech Systems, Inc Fax Branding StatementAppendix Canadian Limitations Notice Appendix Product Safety Compliance +12 VDC, -12 VDC, +5 VDC Figure A-1. Creepage and Clearance Distances EMC, Safety and Terminal Directive Compliance European Low Voltage Directive New Zealand Modem Warning Notice 90/K56flex, ITU V.34 extended, V.34, ITU Appendix B Technical Specifications14,400, 12,000, 9600, 7200, 4800, 2400, ITU Group 3, T.4, T.30, V.21, V.27ter Appendix Fax Carrier Frequencies Hz mark, 1850 Hz space for Transmit Connectors Appendix C Ascii Conversion Chart Code HEX DEC Appendix D FLASHWINFlash Upgrade Introduction MT5634ZPX-PCI Index BBS Auto Retrain Enable/disable V25 data calling tone S35Index Data Fax-back service , 66 FCC Regulations , 68-81 firmware Fall-forward , 7 fallback , 7, 37 fax Tones dialing MT5634ZPX-PCI