Installing Drivers | Multi-Tech Systems MT5634ZPX-PCI guide

2 Installation

Installing Drivers

1.Plug in and turn on your computer. As your computer boots, it automatically detects the MultiModemZPX-PCI, and the New Hardware Found dialog box appears.

2.In the New Hardware Found dialog box, select Driver from disk provided by hardware manufacturer (default selection). Then click OK. The Install from Disk dialog box appears.

3.Insert the MultiModemZPX-PCI Drivers diskette into the computer’s drive, select the drive letter (A:\ is the default), and click OK. The computer installs the software drivers needed to communicate with your MultiModemZPX-PCI and then displays the Windows 95 desktop.

4.Installation of the MultiModemZPX-PCI is complete. If you plan to use the provided communications software, install it now according to the instructions provided in your corresponding software manual.

Verifying Configuration

Windows 95 Plug and Play

Use the following procedure to check the assignments Windows has made for your modem:

1.Click Start, Settings, Control Panel, and then double-click the System icon.

2.When the System Properties dialog box appears, click the Device Manager tab. A list of device types appears.

3.Double-click Modem for a list of modems installed in your computer.

4.Double-clickMulti-Tech MT5634ZPX-PCI. The Modem Properties dialog box for your MultiModemZPX-PCI model appears.

MT5634ZPX-PCI

19

Image 19

Multi-Tech Systems MT5634ZPX-PCI owner manual Installing Drivers, Verifying Configuration

Contents

Model MT5634ZPX-PCI Record of Revisions MT5634ZPX -PCI Contents Technical Support Introduction Initial Checklist Common ProblemsIntroduction Limited Warranty Data is being lost Introduction and Description MT5634ZPX-PCI Introduction and Description Features Fax Peripiheral Component Interconnect PCI Optional V.8bis Sequence Support/FunctionsDownstream Rates Upstream Data Rates Digital Loss and Robbed-bit Signaling Auto Adapt What is in Your Modem Package? Appendix How to Use This Manual You type this Typographic Conventions Installation What You’ll Need Introduction Installation Overview Safety WarningsInstallation Windows 95 Plug and Play Configuring the MultiModem ZPX-PCI Installing the MultiModemZPX-PCI Plug the telephone’s line cable into External ConnectionsWith the modem, insert the microphone Verifying Configuration Installing Drivers Port COM Interrupt Address Speed Is Your MultiModemZPX-PCI Ready for Use? Select Start, Settings, and then Control PanelTo Remove Previous Modem from Windows Simple Operation Operating Your MultiModemZPX-PCI Testing Data Functions Software ConfigurationSelect Start, Programs, Accessories, and then HyperTerminal Connect dialog box, click Dialing Properties Click Start, Programs, Accessories, and then WordPad Testing FAX FunctionsMultiModemZPX-PCI’s fax capabilities Click Start, Programs, Accessories, and then HyperTerminal Testing Voice Function AT+FCLASS=8 AT+VLS=7 MultiModemZPX-PCI’s Speakerphone Test Configuring Communications Software Installation Basic Procedure Remote Configuration Changing the Setup Password Setup PKUNZIP.EXE AT Commands, S-Registers, and Result Codes AT Commands Dial AT Commands, Result Codes, and S-RegistersCommunication Standard Setting Carrier Control Hook Control Echo Command Mode CharactersDS=n Dial Stored Telephone Number Echo Online Data Characters Modulation Handshake Monitor Speaker VolumeMonitor Speaker Mode Return Online to Data Mode Result Code Selection Sr=n Set Register ValueSr? Read Register Value Result Code Format Data Carrier Detect DCD Control Modem ResetLong Space Disconnect Auto Retrain 22bis Guard Tone Control Fn Load Factory Default SettingsCommunications Mode Asynchronous Communications Mode Select Stored Configuration for Hard Reset Self-Test CommandsView Current Configuration Store Current Configuration \Kn Set Break Control \Nn Error Correction Mode Selection\Gn Modem Port Flow Control \Jn Data Buffer Control Data Calling Tone \T n Inactivity Timer\V n Protocol Result Code \X n XON/XOFF Pass-Through Allowed value Enable Synchronous Buffered ModeSpeaker Codec Loopback Registers Minute 255 Decimal Disables, 1-255 enables Modulation50-150 Tones = disable 1 = enable Connect. Where K56flex provided=V.90/56Kflex disabled Data mode 1-4 sets the value to S36=5,7 LAPM, MNP, or Async MNP or AsyncSets one of three 56K operating Result Codes Connected at 52000 bps Connected at 46000 bpsConnected at 48000 bps Connected at 50000 bps Troubleshooting Initial Checklist Troubleshooting Common Problems MT5634ZPX-PCI Modem dials but cannot make a connection Modem disconnects while online Modem cannot connect when answering Data is being lost Warranty, Service, and Tech Support/BBS Limited Warranty Warranty, Service, and Tech Support Online Warranty Registration Recording Modem Information Technical Support Multi-Tech Systems, Inc Woodale Drive Mounds View, MN Service If you know the file name Multi-Tech BBSTo log on to the Multi-Tech BBS To Download a file If you don’t know the file name About CompuServe About the Multi-Tech Fax-Back ServiceAbout the Internet Appendix FCC Regulations for Telephone Line Interconnection Appendix a Regulatory Compliance Appendix Fax Branding StatementMulti-Tech Systems, Inc Canadian Limitations Notice Appendix +12 VDC, -12 VDC, +5 VDC Product Safety Compliance Figure A-1. Creepage and Clearance Distances European Low Voltage Directive EMC, Safety and Terminal Directive Compliance New Zealand Modem Warning Notice ITU Group 3, T.4, T.30, V.21, V.27ter Appendix B Technical Specifications14,400, 12,000, 9600, 7200, 4800, 2400, 90/K56flex, ITU V.34 extended, V.34, ITU Appendix Hz mark, 1850 Hz space for Transmit Fax Carrier Frequencies Connectors Code HEX DEC Appendix C Ascii Conversion Chart Introduction Appendix D FLASHWINFlash Upgrade MT5634ZPX-PCI Index BBS Data Enable/disable V25 data calling tone S35Index Auto Retrain Fall-forward , 7 fallback , 7, 37 fax Fax-back service , 66 FCC Regulations , 68-81 firmware Tones dialing MT5634ZPX-PCI