0300B, 1237, RING, STABILIZER, 16-1/2 ARM | Multiquip BS46H90

STABILIZER RING ASSY.

NO.	PART NO.	PART NAME	QTY.	REMARKS
1	0300B	WASHER, FLAT SAE 5/16	4
2	1237	SCREW, SCH 5/16-18 X 7/8, NYL, NP	4
3	1723	ROD END, 5/16-24 MALE	4
4	6014 C	NUT, HEX FINISH 5/16-24	8
5	1483	RING, STABILIZER, 16-1/2" ARM	1

BS46H SERIES WALK-BEHIND TROWEL • operatION And parts manual — rev. #2 (10/15/13) — page 61

Image 61

Multiquip BS46H90, BS46HLE, BS46H11 manual 0300B, 1237, RING, STABILIZER, 16-1/2 ARM

Contents

Model BS46HLE Fuel and chemical exposure Warnings Silicosis Warning Silicosis/Respiratory Warnings WALK-BEHIND Trowel Table of Contents Completely Training checklist Daily pre-Operation checklist Daily pre-operation checklist SaFeTy meSSageS Safety Information GENEraL SafETy ENgiNE SafETy TrOwEL SafETyOrder Form PT-160 Before servicing equipment TraNSpOrTiNg SafETy FUeL SaFeTy EmISSIONS INFORmaTION ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINgEmission control Label Label must remain with the engine for its entire life Side View Trowel SPECIFICATIONS/DIMENSIONS 11997+A12010 in m/s2 ΣA8 Engine Specifications General information 15 14 13 12 Trowel Components Initial Servicing Engine Components Assembly and Installation Assembly and installationHandle Tube Installation Vibratory T-Handle Bar Placement Pitch Cable Installation Safety Stop Switch ConnectionShown in Figure Ground point Before Starting InspectionEngine Oil Check Belt Check Gearbox OilBelt Guard Check Fuel Check Operation Inspection/operationLifting the Trowel Onto a Slab Lifting Bale Starting the Engine OperationPlace the engine fuel valve lever in the on position Place the choke lever in the Open position Starter Grip Testing the Centrifugal Safety Stop Switch Concrete Finishing Techniques To Begin TrowelingPitching the Blades Standard Handle Pitching the Blades Quick Pitch Handle Maneuvering the Trowel Maneuvering the Trowel Stopping The Engine Place the safety stop switch in the OFF position Combo Blades OptionsClip-On Float Blades Optional Float Discs Optional Quick Pitch Handle Optional Trowel Arm Adjustment Tool Optional Maintenance Engine Air Cleaner General CleanlinessEngine check Spark Plug Engine oilBelt Never use a spark plug of incorrect heat range Blade Pitch Adjustment Procedure Spark arrester cleaning Bushings or bent trowel arms Spider removal Trowel arm removal Changing bladesRemove the trowel arm from the spider plate Checking trowel arm straightness Trowel arm Lever adjustmentEnsure the fixture arm is in the up position Shaft and the test surface Installing Pans Onto Finisher Blades ReAssembly LONG-TERM Storage Troubleshooting engine Troubleshooting Air cleaner dirty? Clean or replace air cleaner Or malfunctioning? Or replace switch if necessary Troubleshooting Walk-Behind Trowel Wiring Diagram Page Explanation of Code in Remarks Column To 3 Units Suggested Spare Parts Nameplate and Decals ISO DECAL, LIFTING/CRUSH, 2.4 X ISO DECAL, Read MANUAL, 2.00 DIAISO DECAL, ASK for TRAINING, 2.00 DIA DECAL, Serial PLATE, WBT-CHINA Standard Handle Assy Switch ASSY., Kill Wire ASSY., Kill SwitchSPACER, Slide Block Guide WASHER, FENDER, 1.5OD X 3/8ID Quick-pitch Handle ASSY. option Adjustment PIN NUT , QP Trim Cntl AdjustmentQP Adjustment Block Spring Center Balance Guard Assy Guard Ring Access PANEL, B FinisherCLIP, Fast Lead SCREW, Fast Lead Requires 26 OZ .8 Liters Gearbox Lubricant for Operation Gearbox Assy FLANGE, Input Shaft SEAL, OILBEARING, CUP, Timken #M11910 GEAR, Worm B Input Shaft Engine and clutch Assy WIRE, Safety Switch CONNECTOR, Splice TAPLifting Bale Assembly B FIN WEIGHT, Automatic Clutch 14 1 Spider Assy Lock Washer 3/8 MED Blade AssemblyBUSHING, Trowel ARM Spider Plate Stabilizer Ring Assy 1237 0300BRING, STABILIZER, 16-1/2 ARM Blade Assy See Notice below 219060201 Guard Ring LUG Ring Engine service parts 28462ZE2W11 17620Z4H02028462ZE3W01 17210ZE2822Page Page HERE’S HOW to GET Help