Nameplate and Decals | Multiquip BS46H90, BS46HLE, BS46H11 instruction

NAMEPLATE AND DECALS

STANDARD

HANDLE

	3			QUICK PITCH™
		5		HANDLE
	4		6

2

1

7

FINISH	J	COMBO	FINISH	B	COMBO
PRELOAD TRIM INDICATOR
FINISH	36”	COMBO	FINISH	48”	COMBO

11

MODEL

SERIAL NO.

10	9	8	12
	9
			WALK-BEHIND
			POWER TROWEL
		WALK-BEHIND
		POWER TROWEL
		WWW.MULTIQUIP.COM

page 46 — BS46H SERIES WALK-BEHIND TROWEL • operation and parts manUAL — rev. #2 (10/15/13)

Image 46

Multiquip BS46H90, BS46HLE, BS46H11 manual Nameplate and Decals

Contents

Model BS46HLE Fuel and chemical exposure Warnings Silicosis/Respiratory Warnings Silicosis Warning Table of Contents WALK-BEHIND Trowel Training checklist Completely Daily pre-operation checklist Daily pre-Operation checklist Safety Information SaFeTy meSSageS GENEraL SafETy Order Form PT-160 TrOwEL SafETyENgiNE SafETy Before servicing equipment FUeL SaFeTy TraNSpOrTiNg SafETy Emission control Label ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINgEmISSIONS INFORmaTION Label must remain with the engine for its entire life Trowel SPECIFICATIONS/DIMENSIONS Side View Engine Specifications 11997+A12010 in m/s2 ΣA8 General information Trowel Components 15 14 13 12 Engine Components Initial Servicing Handle Tube Installation Assembly and installationAssembly and Installation Vibratory T-Handle Bar Placement Shown in Figure Safety Stop Switch ConnectionPitch Cable Installation Ground point Before Starting InspectionEngine Oil Check Belt Guard Check Gearbox OilBelt Check Fuel Check Lifting the Trowel Onto a Slab Inspection/operationOperation Lifting Bale Place the engine fuel valve lever in the on position OperationStarting the Engine Place the choke lever in the Open position Testing the Centrifugal Safety Stop Switch Starter Grip Pitching the Blades Standard Handle To Begin TrowelingConcrete Finishing Techniques Pitching the Blades Quick Pitch Handle Maneuvering the Trowel Maneuvering the Trowel Place the safety stop switch in the OFF position Stopping The Engine Clip-On Float Blades Optional OptionsCombo Blades Float Discs Optional Trowel Arm Adjustment Tool Optional Quick Pitch Handle Optional Maintenance Engine Air Cleaner General CleanlinessEngine check Belt Engine oilSpark Plug Never use a spark plug of incorrect heat range Spark arrester cleaning Blade Pitch Adjustment Procedure Spider removal Bushings or bent trowel arms Trowel arm removal Changing bladesRemove the trowel arm from the spider plate Ensure the fixture arm is in the up position Trowel arm Lever adjustmentChecking trowel arm straightness Shaft and the test surface ReAssembly Installing Pans Onto Finisher Blades LONG-TERM Storage Troubleshooting Troubleshooting engine Air cleaner dirty? Clean or replace air cleaner Or malfunctioning? Or replace switch if necessary Troubleshooting Walk-Behind Trowel Wiring Diagram Page Explanation of Code in Remarks Column Suggested Spare Parts To 3 Units Nameplate and Decals ISO DECAL, ASK for TRAINING, 2.00 DIA ISO DECAL, Read MANUAL, 2.00 DIAISO DECAL, LIFTING/CRUSH, 2.4 X DECAL, Serial PLATE, WBT-CHINA Standard Handle Assy SPACER, Slide Block Guide Wire ASSY., Kill SwitchSwitch ASSY., Kill WASHER, FENDER, 1.5OD X 3/8ID Quick-pitch Handle ASSY. option QP Adjustment Block NUT , QP Trim Cntl AdjustmentAdjustment PIN Spring Center Balance Guard Assy CLIP, Fast Lead Access PANEL, B FinisherGuard Ring SCREW, Fast Lead Gearbox Assy Requires 26 OZ .8 Liters Gearbox Lubricant for Operation BEARING, CUP, Timken #M11910 SEAL, OILFLANGE, Input Shaft GEAR, Worm B Input Shaft Engine and clutch Assy Lifting Bale Assembly B FIN CONNECTOR, Splice TAPWIRE, Safety Switch WEIGHT, Automatic Clutch Spider Assy 14 1 BUSHING, Trowel ARM Blade AssemblyLock Washer 3/8 MED Spider Plate Stabilizer Ring Assy 1237 0300BRING, STABILIZER, 16-1/2 ARM Blade Assy 0201 21906See Notice below Guard Ring LUG Ring Engine service parts 28462ZE3W01 17620Z4H02028462ZE2W11 17210ZE2822Page Page HERE’S HOW to GET Help