Suggested Spare Parts, To 3 Units | Multiquip BS46HLE, BS46H90

Suggested Spare Parts

BS46H90/BS46H11 WALK-BEHIND TROWELS with HONDA gx270UT2QA2/GX340UT2QAP2 gasoline engines

1 to 3 Units

Qty.	P/N	Description
2	20478	GRIP, HANDLE
1	21046	GASKET/SEAL KIT
1	21047	BEARING KIT
1	20285	PITCH CABLE (STD)
1	20297	PITCH CABLE (QP)
1	21172	THROTTLE CABLE
1	10968	THRUST BEARING KIT
1	10793	THRUST COLLAR
1	1154 A	WEAR PLATE
2	0152 3	V-BELT A-28 (BS46H90)
2	1243	V-BELT A-27 (BS46H11)
2	10139	GEARBOX LUBRICANT
1	22732	THROTTLE LEVER ASSY.

NOTICE

Part numbers on this Suggested Spare Parts list may supersede/replace the part numbers shown in the following parts lists.

HONDA gx270UT2QA2
Qty.	P/N	Description
3	9807955876	SPARK PLUG
1	17620z4h020	TANK CAP
3	17210ZE2822	AIR CLEANER ELEMENT
2	17218ZE2821	FILTER OUTER
1	28462ZE2W11	ROPE, RECOIL
HONDA GX340ut2qap2
Qty.	P/N	Description
3	9807956876	SPARK PLUG
1	17620Z4H020	TANK CAP
3	17210ZE3010	AIR CLEANER ELEMENT
3	17218ZE3000	FILTER OUTER
1	28462ZE3W01	ROPE, RECOIL

BS46H SERIES WALK-BEHIND TROWEL • operatION And parts manual — rev. #2 (10/15/13) — page 45

Image 45

Multiquip BS46HLE, BS46H90, BS46H11 manual Suggested Spare Parts, To 3 Units

Contents

Model BS46HLE Fuel and chemical exposure Warnings Silicosis Warning Silicosis/Respiratory Warnings WALK-BEHIND Trowel Table of Contents Completely Training checklist Daily pre-Operation checklist Daily pre-operation checklist SaFeTy meSSageS Safety Information GENEraL SafETy ENgiNE SafETy TrOwEL SafETyOrder Form PT-160 Before servicing equipment TraNSpOrTiNg SafETy FUeL SaFeTy EmISSIONS INFORmaTION ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINgEmission control Label Label must remain with the engine for its entire life Side View Trowel SPECIFICATIONS/DIMENSIONS 11997+A12010 in m/s2 ΣA8 Engine Specifications General information 15 14 13 12 Trowel Components Initial Servicing Engine Components Assembly and Installation Assembly and installationHandle Tube Installation Vibratory T-Handle Bar Placement Pitch Cable Installation Safety Stop Switch ConnectionShown in Figure Ground point Inspection Before StartingEngine Oil Check Belt Check Gearbox OilBelt Guard Check Fuel Check Operation Inspection/operationLifting the Trowel Onto a Slab Lifting Bale Starting the Engine OperationPlace the engine fuel valve lever in the on position Place the choke lever in the Open position Starter Grip Testing the Centrifugal Safety Stop Switch Concrete Finishing Techniques To Begin TrowelingPitching the Blades Standard Handle Pitching the Blades Quick Pitch Handle Maneuvering the Trowel Maneuvering the Trowel Stopping The Engine Place the safety stop switch in the OFF position Combo Blades OptionsClip-On Float Blades Optional Float Discs Optional Quick Pitch Handle Optional Trowel Arm Adjustment Tool Optional Maintenance General Cleanliness Engine Air CleanerEngine check Spark Plug Engine oilBelt Never use a spark plug of incorrect heat range Blade Pitch Adjustment Procedure Spark arrester cleaning Bushings or bent trowel arms Spider removal Changing blades Trowel arm removalRemove the trowel arm from the spider plate Checking trowel arm straightness Trowel arm Lever adjustmentEnsure the fixture arm is in the up position Shaft and the test surface Installing Pans Onto Finisher Blades ReAssembly LONG-TERM Storage Troubleshooting engine Troubleshooting Air cleaner dirty? Clean or replace air cleaner Or malfunctioning? Or replace switch if necessary Troubleshooting Walk-Behind Trowel Wiring Diagram Page Explanation of Code in Remarks Column To 3 Units Suggested Spare Parts Nameplate and Decals ISO DECAL, LIFTING/CRUSH, 2.4 X ISO DECAL, Read MANUAL, 2.00 DIAISO DECAL, ASK for TRAINING, 2.00 DIA DECAL, Serial PLATE, WBT-CHINA Standard Handle Assy Switch ASSY., Kill Wire ASSY., Kill SwitchSPACER, Slide Block Guide WASHER, FENDER, 1.5OD X 3/8ID Quick-pitch Handle ASSY. option Adjustment PIN NUT , QP Trim Cntl AdjustmentQP Adjustment Block Spring Center Balance Guard Assy Guard Ring Access PANEL, B FinisherCLIP, Fast Lead SCREW, Fast Lead Requires 26 OZ .8 Liters Gearbox Lubricant for Operation Gearbox Assy FLANGE, Input Shaft SEAL, OILBEARING, CUP, Timken #M11910 GEAR, Worm B Input Shaft Engine and clutch Assy WIRE, Safety Switch CONNECTOR, Splice TAPLifting Bale Assembly B FIN WEIGHT, Automatic Clutch 14 1 Spider Assy Lock Washer 3/8 MED Blade AssemblyBUSHING, Trowel ARM Spider Plate Stabilizer Ring Assy 0300B 1237RING, STABILIZER, 16-1/2 ARM Blade Assy See Notice below 219060201 Guard Ring LUG Ring Engine service parts 28462ZE2W11 17620Z4H02028462ZE3W01 17210ZE2822Page Page HERE’S HOW to GET Help