Stabilizer Ring Assy | Multiquip BS46HLE, BS46H90, BS46H11 manual

STABILIZER RING ASSY.

5

4

1

SEE DETAIL “A”

DETAIL “A”

4

3 1

1

2

APPLY LOCTITE 242 BLUE

1 OR EQUIVALENT.

page 60 — BS46H SERIES WALK-BEHIND TROWEL • operation and parts manUAL — rev. #2 (10/15/13)

Image 60

Multiquip BS46HLE, BS46H90, BS46H11 manual Stabilizer Ring Assy

Contents

Model BS46HLE Fuel and chemical exposure Warnings Silicosis/Respiratory Warnings Silicosis Warning Table of Contents WALK-BEHIND Trowel Training checklist Completely Daily pre-operation checklist Daily pre-Operation checklist Safety Information SaFeTy meSSageS GENEraL SafETy TrOwEL SafETy ENgiNE SafETyOrder Form PT-160 Before servicing equipment FUeL SaFeTy TraNSpOrTiNg SafETy ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINg EmISSIONS INFORmaTIONEmission control Label Label must remain with the engine for its entire life Trowel SPECIFICATIONS/DIMENSIONS Side View Engine Specifications 11997+A12010 in m/s2 ΣA8 General information Trowel Components 15 14 13 12 Engine Components Initial Servicing Assembly and installation Assembly and InstallationHandle Tube Installation Vibratory T-Handle Bar Placement Safety Stop Switch Connection Pitch Cable InstallationShown in Figure Ground point Inspection Before StartingEngine Oil Check Gearbox Oil Belt CheckBelt Guard Check Fuel Check Inspection/operation OperationLifting the Trowel Onto a Slab Lifting Bale Operation Starting the EnginePlace the engine fuel valve lever in the on position Place the choke lever in the Open position Testing the Centrifugal Safety Stop Switch Starter Grip To Begin Troweling Concrete Finishing TechniquesPitching the Blades Standard Handle Pitching the Blades Quick Pitch Handle Maneuvering the Trowel Maneuvering the Trowel Place the safety stop switch in the OFF position Stopping The Engine Options Combo BladesClip-On Float Blades Optional Float Discs Optional Trowel Arm Adjustment Tool Optional Quick Pitch Handle Optional Maintenance General Cleanliness Engine Air CleanerEngine check Engine oil Spark PlugBelt Never use a spark plug of incorrect heat range Spark arrester cleaning Blade Pitch Adjustment Procedure Spider removal Bushings or bent trowel arms Changing blades Trowel arm removalRemove the trowel arm from the spider plate Trowel arm Lever adjustment Checking trowel arm straightnessEnsure the fixture arm is in the up position Shaft and the test surface ReAssembly Installing Pans Onto Finisher Blades LONG-TERM Storage Troubleshooting Troubleshooting engine Air cleaner dirty? Clean or replace air cleaner Or malfunctioning? Or replace switch if necessary Troubleshooting Walk-Behind Trowel Wiring Diagram Page Explanation of Code in Remarks Column Suggested Spare Parts To 3 Units Nameplate and Decals ISO DECAL, Read MANUAL, 2.00 DIA ISO DECAL, LIFTING/CRUSH, 2.4 XISO DECAL, ASK for TRAINING, 2.00 DIA DECAL, Serial PLATE, WBT-CHINA Standard Handle Assy Wire ASSY., Kill Switch Switch ASSY., KillSPACER, Slide Block Guide WASHER, FENDER, 1.5OD X 3/8ID Quick-pitch Handle ASSY. option NUT , QP Trim Cntl Adjustment Adjustment PINQP Adjustment Block Spring Center Balance Guard Assy Access PANEL, B Finisher Guard RingCLIP, Fast Lead SCREW, Fast Lead Gearbox Assy Requires 26 OZ .8 Liters Gearbox Lubricant for Operation SEAL, OIL FLANGE, Input ShaftBEARING, CUP, Timken #M11910 GEAR, Worm B Input Shaft Engine and clutch Assy CONNECTOR, Splice TAP WIRE, Safety SwitchLifting Bale Assembly B FIN WEIGHT, Automatic Clutch Spider Assy 14 1 Blade Assembly Lock Washer 3/8 MEDBUSHING, Trowel ARM Spider Plate Stabilizer Ring Assy 0300B 1237RING, STABILIZER, 16-1/2 ARM Blade Assy 21906 See Notice below0201 Guard Ring LUG Ring Engine service parts 17620Z4H020 28462ZE2W1128462ZE3W01 17210ZE2822Page Page HERE’S HOW to GET Help