Fuse Information

Refer to Figure 45 for location on fuse panel.

		Table 3. Fuses
Fuse Number	Amps	Designator	Functions Fused
1	20	T13	MCU Power
1	20	T21	Service Port Connector
		T21	Service Port Connector
2	20	T3	Oil Cooler
3	5	T5	Light Switch
3	5	T15	Pitch Switches
		T15	Pitch Switches
4	20	T6	Left Lights
5	7.5	T23	Sprayers
6	20	T7	Right Lights

		Table 4. Ground
Location	Designator	Functions Grounded

Top Left	T12	MCU

	T14	Pitch Switch, Throttle, Cruise, LED's, Cluster gauge
	T14	Pitch Switch, Throttle, Cruise, LED's, Cluster gauge

Middle Left	T20	Service Port Connector

	T24	Spray Pumps
	T24	Spray Pumps

	T25	Rear Lights

Bottom Left	T26	Pitch Switch, Throttle, Cruise, LED's, Cluster gauge

	T28	Engine Harness

Bottom Right	T1	Pitch Valves

	T2	Control Relay
	T2	Control Relay

Middle Right	T4	Cooler Fan

	T27	Front Right Lights
	T27	Front Right Lights

Top Right	T31	PRM (Power Relay Module)

	T32	Hour Meter
	T32	Hour Meter

FUSE PANEL

TL			TR
GROUND ML			MR GROUND
BL	20	20	BR
	5	20
FUSES	7.5	20	FUSES

Figure 45. Fuse and Ground Location

PAGE 30 — HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #1 (01/24/14)

Page 30

Image 30

Multiquip HTXD6i / STXD6i manual Fuse Information, Refer to for location on fuse panel

Contents

Model HTXD6i/STXD6i This Manual Must Accompany the Equipment AT ALL Times Table of Contents HTX6Di/STX6Di Trowel Machine Information and Maintenance LOG Safety Information Safety Messages General Safety „ALWAYS know the location of the nearest Order Form PT-160 Trowel SafetyEngine Safety Before servicing equipment „ Never tamper with the factory settings Fuel SafetyBattery Safety „ Use well-insulated gloves when picking up the battery Lifting Transporting SafetyTowing Safety „ Always shutdown engine before transporting Environmental Safety Tools Needed Machine Information ModelSerial Number General Procedures Setup Jumper InstallationRemove Setup Jumper If installed Hydraulic Oil Check Initial Check and AdjustmentsOIL and Coolant Check Loosen 1-1/16 jam nut on charge relief valve Item A, Figure Engine Oil Engine CoolantEnsure engine is level Service Tool Setup and Connection Click Cancel again when the new screen comes up Input the license key obtained from Multiquip and click OK WST Tool Bar Click Finish on the next screen to complete installation Laptop ConfigurationConnection Procedure Necessary to crank or turn on the engine Calibrate Foot Pedal Machine Setup and CalibrationSensor Adjustment Click Calibration button in Pedal Sensor frame Figure Secondary Hydraulic Fill Procedures CalibrationPress Start button to begin calibration and follow prompts Pitch Pressure Check Machine Pressure AdjustmentCharge Pressure Adjustment Restart machine Pitch Pressure Adjustment Steering Pressure AdjustmentReturn engine rpm to idle Turn off machine and remove gauge Left Side Trowel Speed Adjustment Trowel Speed ADJUSTMENT\SETUPAdjust Zero Stroke Position Lower trowel and shut off Loosen Jamb nut Item D, Figure Right Side Trowel Speed Adjustment Remove setup jumper or re-enable stroke followerCalibrate Stroke Sensor Pitch Setup Flatten Blades Leading Edge Height Adjustment Measure Blade Leading Edge Height Set Zero Pitch Cylinder Stops Pitch Sensor Calibration Gauge Turn machine off for 10 seconds Inspection Fluid LevelsMechanical Switch smart pitch switch to off position Static Blade Pitch Drift Test Fuse Information Refer to for location on fuse panelPage HERE’S HOW to GET Help

FUSE INFORMATION

Refer to Figure 45 for location on fuse panel.

Table 3. Fuses

Amps

Designator

Functions Fused

Table 4. Ground

Designator

Functions Grounded

MCU

Figure 45. Fuse and Ground Location

PAGE 30 — HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #1 (01/24/14)