Manuals / Multiquip / Power Tools / Saw

Multiquip SP-6457 TD operation manual Night Light, Transportation Tie-downs and Lift Point

Models: SP-6457 TD

1 69

Download 69 pages 13.49 Kb

Page 41

Night Light

The night light can be used on either side of the saw, and can be extended and rotated for best illumination of the cutting area. Aim the light, then lock it in position by tightening the lock knobs. The light can be removed for storage by loosening the lock knobs, disconnecting the light cord and sliding the light bar out of the saw.

Lock
Knob	Lock
	Lock
	Knob

Fig. 22 — Night Light

Transportation Tie-downs and Lift Point

Tie-downs

The saw is provided with holes at each corner of the lower frame for easy tie- down during transportation. The ½” all-thread J-bolts, with which your saw was attached to its shipping pallet, can be used in a variety of tie-down scenarios. It is highly recommended that the saw be tied down any time it is being transported.

Tie-down

Tie-down

Fig. 23 —Tie-down Points

41

Image 41

Multiquip SP-6457 TD operation manual Night Light, Transportation Tie-downs and Lift Point

Contents

SP-6457 TD Concrete Saw For Help & Information Contact Multiquip Conventions California Proposition 65 Warning Table of Contents Specifications Safety Hazard Symbols Rotating Blades Skin Injection Hazard Rules for Safe Operation General Safety WarningsPage General Safety Precautions Blade Safety SAW Transportation Safety Machine Operation and Safety Decals Model no SPEC. no Serial no Serial TagEngine Serial Before Starting OperationBlade Shaft Ratios Engine Power, Cutting Power & Sheave Size18612 Blade RPM vs. Surface Feet Per Minute Sfpm Installing the Blade Installing the BladeBlade Stacking Stacking Blades for Wide CutsInstalling the Blade Guard Installing and Removing the Blade GuardBlade Guard Water Supply Collar Guard, Installed Installing the Collar GuardWater Supply System Water Supply and ControlON-OFF Control PanelHandlebar Positions HandlebarsFueling the Saw UseRestarting After Running Out of Fuel Starting and Stopping The EngineGlow Plugs Cold Weather OperationBlock Heaters Draining the Water SystemPointer Adjustment Pointer AdjustmentJoystick Handle Controls Raise Lower ControlsSetting the Depth Stop Setting the Depth IndicatorDrive System Controls Drive SystemTransaxle Transaxle4-Speed Blade Shaft Speed Blade ShaftGear Shift Components Shifting GearsTie-downs Night LightTransportation Tie-downs and Lift Point Lift Point Lift PointRemovable Guards and Access Panels MaintenanceBelt Tension Belts and PulleysEngine Mount Lock Bolts Adjusting Blade Shaft Drive Belt TensionReplacing the Jackshaft Belt Replacing the Blade Shaft BeltDo not OVER-TIGHTEN Rotary Belt TensionerBlade Shaft Replacement Blade Shaft MaintenanceRemoving the Inner Blade Collar Blade Collar Removal/InstallationInstalling the Inner Blade Collar Installing the Inner Blade CollarInner Collar Blade Shaft Circuit Breakers Maximum Cut Depth AdjustmentLubrication Engine Air and Oil Filter ChartAttaching the PTO Bearing Puller to the Drive Plate Assembly PTO Drive MaintenanceRe-Assembling the PTO Drive PTO Drive Sheave/Bearing AssemblyEngine Rotated Forward to Remove the Battery Replacing the BatteryRaise-Lower System Raise/Lower TroubleshootingJoystick Adjustment Joystick Tension AdjustmentRoutine Maintenance Hydraulic System MaintenanceTo drain the hydraulic system Draining & Filling the Hydraulic SystemTo fill the hydraulic system Bleeding the Depth Stop Cylinder Bleeding the Depth Stop CylinderDrive Wheel Alignment Drive Wheel AlignmentPivot Side Adjustment Side Specifications Dimensions Electric Diagram Www multiquip.com