Manuals
/
Brands
/
Computer Equipment
/
Network Hardware
/
NEC
/
Computer Equipment
/
Network Hardware
NEC
151944 system manual
- page 8
1
8
78
78
Download
78 pages, 922.25 Kb
LIST OF TABLES
ND-46550 (E)
Page vi
Revision 2.0
This page is for your notes.
Contents
Main
Page
NEAX2000 IVS Remote PIM System Manual
TABLE OF CONTENTS
Page
LIST OF FIGURES
Page
LIST OF TABLES
Page
CHAPTER 1 INTRODUCTION
Page
CHAPTER 2 SYSTEM DESCRIPTION
Page
ND-46550 (E) CHAPTER 2 Page 5
3. SYSTEM CONFIGURATION Figure 2-2 shows the system configuration.
Figure 2-2 System Configuration
Page
Page
Page
Page
CHAPTER 2 ND-46550 (E) Page 10
Figure 2-3 Time Slot Allocation
Note: The control signalling channel is set by SW2 of DAIA/DAIB. Refer to Chapter 3 sections 2.1.1
and 2.2.1 for the switch settings.
ND-46550 (E) CHAPTER 2 Page 11
Figure 2-4 Time Slot Allocation (Con t inu ed)
2.2.1 for the switch settings.
Page
CHAPTER 3 INSTALLA TION
ATT E N TI O N
Page
CHAPTER 3 ND-46550 (E) Page 16
Figure 3-3 Installation Procedure for Main Site
Remote PIM System. Refer to the Installation Procedure Manual for regular installation.
Installation Procedure Manual
Circuit Card Manual
ND-46550 (E) CHAPTER 3 Page 17
Figure 3-4 Installation Procedure for Remote Site
System. Refer to the Installation Procedure Manual for the procedures marked by * .
the link between the main site and the remote site is lost.
CHAPTER 3 ND-46550 (E) Page 18
Figure 3-5 PN-DAIA Card
Page
Page
Page
Page
*
Page
Page
Page
Page
Page
ND-46550 (E) CHAPTER 3 Page 29
Figure 3-9 BUS-DAIA Cable Connection
CHAPTER 3 ND-46550 (E) Page 30
Figure 3-10 DAIA-DAIC Cable Connection
ND-46550 (E) CHAPTER 3 Page 31
Figure 3-11 DAIA-DAIC Cable Connection (Continued)
CHAPTER 3 ND-46550 (E) Page 32
Figure 3-12 DAIA-DAIC Cable Connection (Continued)
ND-46550 (E) CHAPTER 3 Page 33
Figure 3-13 DAIA-DAIC Cable Connection (Continued)
CHAPTER 3 ND-46550 (E) Page 34
Figure 3-14 PN-DAIB Card
Page
Page
Page
Page
ND-46550 (E) CHAPTER 3 Page 39
Figure 3-15 Mounting Location of DAIB Card
CHAPTER 3 ND-46550 (E) Page 40
Figure 3-16 Mounting Location of DAIB Card (Cont i nued )
Page
CHAPTER 3 ND-46550 (E) Page 42
Figure 3-18 Mounting Location of DAIC Card (Re mot e PI M ) (Continued)
ND-46550 (E) CHAPTER 3 Page 43
Figure 3-19 Mounting Location of DAIC Card (Re mot e PI M ) (Continued)
Page
Page
CHAPTER 3 ND-46550 (E) Page 46
Figure 3-22 Location of Each LEN (Small Platform)
Note: A maximum of 64 line/trunks can be accommodated in one Remote PIM.
ND-46550 (E) CHAPTER 3 Page 47
Figure 3-23 LTC Connector Pin A rrangement (Small Platform)
Page
ND-46550 (E) CHAPTER 3 Page 49
LEN
LT03LT 02LT 01SLOT No.
MDF via the backplane (LTC cables).
Note 4: When DAIC is mounted in slot LT07, slot LT06 must use 4-port Line/Trunk card.
When opposite DAIA card is set to FP No.2:
LT0 6LT05LT04 LT 08LT0 7
LT0 0
CHAPTER 3 ND-46550 (E) Page 50
Figure 3-26 LTC Connector Pin Arrangement (1000 IVS)
Page
CHAPTER 3 ND-46550 (E) Page 52
Figure 3-28 Location of Each LEN (PIM N_UB)
Note: A maximum of 60 line/trunks can be accommodated in one Remote PIM.
ND-46550 (E) CHAPTER 3 Page 53
Figure 3-29 LTC Connector Pin Arrangement (PIM B - UB)
Page
ND-46550 (E) CHAPTER 3 Page 55
Figure 3-31 MDF Cross Connection for PFT (PN-AUCA)
CHAPTER 3 ND-46550 (E) Page 56
Note
ations from Central Office to the PBX; line quality cannot be assured.
Page
Page
ND-46550 (E) CHAPTER 3 Page 59
Figure 3-35 PFT Connector Pin Assignment
CHAPTER 3 ND-46550 (E) Page 60
Figure 3-36 MDF Cross Connection for PFT (PZ-8PFTA)
ND-46550 (E) CHAPTER 3 Page 61
Figure 3-36 MDF Cross Connection for PFT (PZ-8PFTA) (Continued)
Page
ND-46550 (E) CHAPTER 3 Page 63
Figure 3-38 Example of DTI Cable Connection vi a LTC Connector
CHAPTER 3 ND-46550 (E) Page 64
between the Main PIM and the Remote PIM.
Note 2: When the DAIA card is mounted in the MP/FP slot, be sure to connect the cable to the CN con-
nector on the DAIA card.
/
ND-46550 (E) CHAPTER 3 Page 65
1312 ft. (400 m) between the Main PIM and the Remote PIM.
Page
CHAPTER 4 TROUBLESHOOTING