Manuals / Brands / Computer Equipment / Network Hardware / NEC / Computer Equipment / Network Hardware

NEC 151944 CHAPTER 3 ND-46550 (E) Page 30, Figure 3-10 DAIA-DAIC Cable Connection

1 78

Download 78 pages, 922.25 Kb

CHAPTER 3 ND-46550 (E)

Page 30

Revision 2.0

(2) Cable Connection between DAIA Card and DAIC CardConnect the DAIC card to the DAIA card by the 48-TW-0.2 CONN CA, as shown in Figure 3- 10.

Figure 3-10 DAIA-DAIC Cable Connection

(1) 1-PIM Configuratio n

: RMT PCM-0.3 CA

: 17-TW-0.3 CONN CA-A

DAIC BUS

• When mo unting 1 DAIA card and 1 DAIC card

• When m ounting 2 DAIA cards and 2 DAIC cards

TBUS

RBUS

CN2

CN1

• When m ounting 3 DAIA cards and 3 DAIC cards

PIM0

: 48-TW-0.2 CONN CA

DAIA

PCM1

PCM0

DAIC BUS

TBUS

RBUS

CN2

CN1

PIM0

DAIA

PCM1

PCM0

DAIC BUS

TBUS

RBUS

CN2

CN1

PIM0

DAIA

PCM1

PCM0

DAICDAIA

DAICDAI ADAICDAIA

Contents

Main Page NEAX2000 IVS Remote PIM System Manual TABLE OF CONTENTS Page LIST OF FIGURES Page LIST OF TABLES Page CHAPTER 1 INTRODUCTION Page CHAPTER 2 SYSTEM DESCRIPTION Page ND-46550 (E) CHAPTER 2 Page 5 3. SYSTEM CONFIGURATION Figure 2-2 shows the system configuration. Figure 2-2 System Configuration Page Page Page Page CHAPTER 2 ND-46550 (E) Page 10 Figure 2-3 Time Slot Allocation Note: The control signalling channel is set by SW2 of DAIA/DAIB. Refer to Chapter 3 sections 2.1.1 and 2.2.1 for the switch settings. ND-46550 (E) CHAPTER 2 Page 11 Figure 2-4 Time Slot Allocation (Con t inu ed) 2.2.1 for the switch settings. Page CHAPTER 3 INSTALLA TION ATT E N TI O N Page CHAPTER 3 ND-46550 (E) Page 16 Figure 3-3 Installation Procedure for Main Site Remote PIM System. Refer to the Installation Procedure Manual for regular installation. Installation Procedure Manual Circuit Card Manual ND-46550 (E) CHAPTER 3 Page 17 Figure 3-4 Installation Procedure for Remote Site System. Refer to the Installation Procedure Manual for the procedures marked by * . the link between the main site and the remote site is lost. CHAPTER 3 ND-46550 (E) Page 18 Figure 3-5 PN-DAIA Card Page Page Page Page * Page Page Page Page Page ND-46550 (E) CHAPTER 3 Page 29 Figure 3-9 BUS-DAIA Cable Connection CHAPTER 3 ND-46550 (E) Page 30 Figure 3-10 DAIA-DAIC Cable Connection ND-46550 (E) CHAPTER 3 Page 31 Figure 3-11 DAIA-DAIC Cable Connection (Continued) CHAPTER 3 ND-46550 (E) Page 32 Figure 3-12 DAIA-DAIC Cable Connection (Continued) ND-46550 (E) CHAPTER 3 Page 33 Figure 3-13 DAIA-DAIC Cable Connection (Continued) CHAPTER 3 ND-46550 (E) Page 34 Figure 3-14 PN-DAIB Card Page Page Page Page ND-46550 (E) CHAPTER 3 Page 39 Figure 3-15 Mounting Location of DAIB Card CHAPTER 3 ND-46550 (E) Page 40 Figure 3-16 Mounting Location of DAIB Card (Cont i nued ) Page CHAPTER 3 ND-46550 (E) Page 42 Figure 3-18 Mounting Location of DAIC Card (Re mot e PI M ) (Continued) ND-46550 (E) CHAPTER 3 Page 43 Figure 3-19 Mounting Location of DAIC Card (Re mot e PI M ) (Continued) Page Page CHAPTER 3 ND-46550 (E) Page 46 Figure 3-22 Location of Each LEN (Small Platform) Note: A maximum of 64 line/trunks can be accommodated in one Remote PIM. ND-46550 (E) CHAPTER 3 Page 47 Figure 3-23 LTC Connector Pin A rrangement (Small Platform) Page ND-46550 (E) CHAPTER 3 Page 49 LEN LT03LT 02LT 01SLOT No. MDF via the backplane (LTC cables). Note 4: When DAIC is mounted in slot LT07, slot LT06 must use 4-port Line/Trunk card. When opposite DAIA card is set to FP No.2: LT0 6LT05LT04 LT 08LT0 7 LT0 0 CHAPTER 3 ND-46550 (E) Page 50 Figure 3-26 LTC Connector Pin Arrangement (1000 IVS) Page CHAPTER 3 ND-46550 (E) Page 52 Figure 3-28 Location of Each LEN (PIM N_UB) Note: A maximum of 60 line/trunks can be accommodated in one Remote PIM. ND-46550 (E) CHAPTER 3 Page 53 Figure 3-29 LTC Connector Pin Arrangement (PIM B - UB) Page ND-46550 (E) CHAPTER 3 Page 55 Figure 3-31 MDF Cross Connection for PFT (PN-AUCA) CHAPTER 3 ND-46550 (E) Page 56 Note ations from Central Office to the PBX; line quality cannot be assured. Page Page ND-46550 (E) CHAPTER 3 Page 59 Figure 3-35 PFT Connector Pin Assignment CHAPTER 3 ND-46550 (E) Page 60 Figure 3-36 MDF Cross Connection for PFT (PZ-8PFTA) ND-46550 (E) CHAPTER 3 Page 61 Figure 3-36 MDF Cross Connection for PFT (PZ-8PFTA) (Continued) Page ND-46550 (E) CHAPTER 3 Page 63 Figure 3-38 Example of DTI Cable Connection vi a LTC Connector CHAPTER 3 ND-46550 (E) Page 64 between the Main PIM and the Remote PIM. Note 2: When the DAIA card is mounted in the MP/FP slot, be sure to connect the cable to the CN con- nector on the DAIA card. / ND-46550 (E) CHAPTER 3 Page 65 1312 ft. (400 m) between the Main PIM and the Remote PIM. Page CHAPTER 4 TROUBLESHOOTING