NEC 151944 - page 16

CHAPTER 2 ND-46550 (E)

Page 8

Revision 2.0

5. SYSTEM CAPACITY

Table 2-3 shows the system capacity.

Note 1: 1 port is used for the control signaling channel.

Note 2: This number refers to the maximum number of remote offices. The remote office can have only one re-

mote PIM.

Note 3: When the main site consists of 7 or 8 PIMs, a Remote PIM cannot be provided.

Table 2-3 System Capacity

DESCRIPTION

CAPACITY

REMARKS

MAIN PIM REMOTE PIM

2000 IVS SMALL

PLATFORM

(72 Port)

1000 IVS

(48 Port)

Max. number of DAIA card 3 - -

Max. number of DAIB card - 1 1

Max. number of DAIC card 6 2 1

Max. number of ports on

Remote Site -24

Note 1 24

Note 1 Main PIM :DAIA

Remote PIM :DAIB

Note 1 48

Note 1 Main PIM :1 DAIA, 2 DAIC

Remote PIM :1 DAIB, 2 DAIC

Note 1 -Main PIM :1 DAIA, 2 DAIC

Remote PIM :1 DAIB, 2 DAIC

Number of PIM

1, 2 3

Note 2 3Number of PIM depends on the

number of Main PIM and

Remote PIM. (Refer to Chapter,

Section 2.)

3, 4 2

Note 2 2

Note 2

5, 6 11

Note 2

7, 8 0

Note 3 0

Note 3

Contents

Main Page NEAX2000 IVS Remote PIM System Manual TABLE OF CONTENTS Page LIST OF FIGURES Page LIST OF TABLES Page CHAPTER 1 INTRODUCTION Page CHAPTER 2 SYSTEM DESCRIPTION Page ND-46550 (E) CHAPTER 2 Page 5 3. SYSTEM CONFIGURATION Figure 2-2 shows the system configuration. Figure 2-2 System Configuration Page Page Page Page CHAPTER 2 ND-46550 (E) Page 10 Figure 2-3 Time Slot Allocation Note: The control signalling channel is set by SW2 of DAIA/DAIB. Refer to Chapter 3 sections 2.1.1 and 2.2.1 for the switch settings. ND-46550 (E) CHAPTER 2 Page 11 Figure 2-4 Time Slot Allocation (Con t inu ed) 2.2.1 for the switch settings. Page CHAPTER 3 INSTALLA TION ATT E N TI O N Page CHAPTER 3 ND-46550 (E) Page 16 Figure 3-3 Installation Procedure for Main Site Remote PIM System. Refer to the Installation Procedure Manual for regular installation. Installation Procedure Manual Circuit Card Manual ND-46550 (E) CHAPTER 3 Page 17 Figure 3-4 Installation Procedure for Remote Site System. Refer to the Installation Procedure Manual for the procedures marked by * . the link between the main site and the remote site is lost. CHAPTER 3 ND-46550 (E) Page 18 Figure 3-5 PN-DAIA Card Page Page Page Page * Page Page Page Page Page ND-46550 (E) CHAPTER 3 Page 29 Figure 3-9 BUS-DAIA Cable Connection CHAPTER 3 ND-46550 (E) Page 30 Figure 3-10 DAIA-DAIC Cable Connection ND-46550 (E) CHAPTER 3 Page 31 Figure 3-11 DAIA-DAIC Cable Connection (Continued) CHAPTER 3 ND-46550 (E) Page 32 Figure 3-12 DAIA-DAIC Cable Connection (Continued) ND-46550 (E) CHAPTER 3 Page 33 Figure 3-13 DAIA-DAIC Cable Connection (Continued) CHAPTER 3 ND-46550 (E) Page 34 Figure 3-14 PN-DAIB Card Page Page Page Page ND-46550 (E) CHAPTER 3 Page 39 Figure 3-15 Mounting Location of DAIB Card CHAPTER 3 ND-46550 (E) Page 40 Figure 3-16 Mounting Location of DAIB Card (Cont i nued ) Page CHAPTER 3 ND-46550 (E) Page 42 Figure 3-18 Mounting Location of DAIC Card (Re mot e PI M ) (Continued) ND-46550 (E) CHAPTER 3 Page 43 Figure 3-19 Mounting Location of DAIC Card (Re mot e PI M ) (Continued) Page Page CHAPTER 3 ND-46550 (E) Page 46 Figure 3-22 Location of Each LEN (Small Platform) Note: A maximum of 64 line/trunks can be accommodated in one Remote PIM. ND-46550 (E) CHAPTER 3 Page 47 Figure 3-23 LTC Connector Pin A rrangement (Small Platform) Page ND-46550 (E) CHAPTER 3 Page 49 LEN LT03LT 02LT 01SLOT No. MDF via the backplane (LTC cables). Note 4: When DAIC is mounted in slot LT07, slot LT06 must use 4-port Line/Trunk card. When opposite DAIA card is set to FP No.2: LT0 6LT05LT04 LT 08LT0 7 LT0 0 CHAPTER 3 ND-46550 (E) Page 50 Figure 3-26 LTC Connector Pin Arrangement (1000 IVS) Page CHAPTER 3 ND-46550 (E) Page 52 Figure 3-28 Location of Each LEN (PIM N_UB) Note: A maximum of 60 line/trunks can be accommodated in one Remote PIM. ND-46550 (E) CHAPTER 3 Page 53 Figure 3-29 LTC Connector Pin Arrangement (PIM B - UB) Page ND-46550 (E) CHAPTER 3 Page 55 Figure 3-31 MDF Cross Connection for PFT (PN-AUCA) CHAPTER 3 ND-46550 (E) Page 56 Note ations from Central Office to the PBX; line quality cannot be assured. Page Page ND-46550 (E) CHAPTER 3 Page 59 Figure 3-35 PFT Connector Pin Assignment CHAPTER 3 ND-46550 (E) Page 60 Figure 3-36 MDF Cross Connection for PFT (PZ-8PFTA) ND-46550 (E) CHAPTER 3 Page 61 Figure 3-36 MDF Cross Connection for PFT (PZ-8PFTA) (Continued) Page ND-46550 (E) CHAPTER 3 Page 63 Figure 3-38 Example of DTI Cable Connection vi a LTC Connector CHAPTER 3 ND-46550 (E) Page 64 between the Main PIM and the Remote PIM. Note 2: When the DAIA card is mounted in the MP/FP slot, be sure to connect the cable to the CN con- nector on the DAIA card. / ND-46550 (E) CHAPTER 3 Page 65 1312 ft. (400 m) between the Main PIM and the Remote PIM. Page CHAPTER 4 TROUBLESHOOTING