Manuals
/
Brands
/
Computer Equipment
/
Network Hardware
/
NEC
/
Computer Equipment
/
Network Hardware
NEC
151944
- page 20
1
20
78
78
Download
78 pages, 922.25 Kb
CHAPTER 2
ND-46550 (E)
Page 12
Revision 2.
0
This page is for your notes.
Contents
Main
Page
NEAX2000 IVS Remote PIM System Manual
TABLE OF CONTENTS
Page
LIST OF FIGURES
Page
LIST OF TABLES
Page
CHAPTER 1 INTRODUCTION
Page
CHAPTER 2 SYSTEM DESCRIPTION
Page
ND-46550 (E) CHAPTER 2 Page 5
3. SYSTEM CONFIGURATION Figure 2-2 shows the system configuration.
Figure 2-2 System Configuration
Page
Page
Page
Page
CHAPTER 2 ND-46550 (E) Page 10
Figure 2-3 Time Slot Allocation
Note: The control signalling channel is set by SW2 of DAIA/DAIB. Refer to Chapter 3 sections 2.1.1
and 2.2.1 for the switch settings.
ND-46550 (E) CHAPTER 2 Page 11
Figure 2-4 Time Slot Allocation (Con t inu ed)
2.2.1 for the switch settings.
Page
CHAPTER 3 INSTALLA TION
ATT E N TI O N
Page
CHAPTER 3 ND-46550 (E) Page 16
Figure 3-3 Installation Procedure for Main Site
Remote PIM System. Refer to the Installation Procedure Manual for regular installation.
Installation Procedure Manual
Circuit Card Manual
ND-46550 (E) CHAPTER 3 Page 17
Figure 3-4 Installation Procedure for Remote Site
System. Refer to the Installation Procedure Manual for the procedures marked by * .
the link between the main site and the remote site is lost.
CHAPTER 3 ND-46550 (E) Page 18
Figure 3-5 PN-DAIA Card
Page
Page
Page
Page
*
Page
Page
Page
Page
Page
ND-46550 (E) CHAPTER 3 Page 29
Figure 3-9 BUS-DAIA Cable Connection
CHAPTER 3 ND-46550 (E) Page 30
Figure 3-10 DAIA-DAIC Cable Connection
ND-46550 (E) CHAPTER 3 Page 31
Figure 3-11 DAIA-DAIC Cable Connection (Continued)
CHAPTER 3 ND-46550 (E) Page 32
Figure 3-12 DAIA-DAIC Cable Connection (Continued)
ND-46550 (E) CHAPTER 3 Page 33
Figure 3-13 DAIA-DAIC Cable Connection (Continued)
CHAPTER 3 ND-46550 (E) Page 34
Figure 3-14 PN-DAIB Card
Page
Page
Page
Page
ND-46550 (E) CHAPTER 3 Page 39
Figure 3-15 Mounting Location of DAIB Card
CHAPTER 3 ND-46550 (E) Page 40
Figure 3-16 Mounting Location of DAIB Card (Cont i nued )
Page
CHAPTER 3 ND-46550 (E) Page 42
Figure 3-18 Mounting Location of DAIC Card (Re mot e PI M ) (Continued)
ND-46550 (E) CHAPTER 3 Page 43
Figure 3-19 Mounting Location of DAIC Card (Re mot e PI M ) (Continued)
Page
Page
CHAPTER 3 ND-46550 (E) Page 46
Figure 3-22 Location of Each LEN (Small Platform)
Note: A maximum of 64 line/trunks can be accommodated in one Remote PIM.
ND-46550 (E) CHAPTER 3 Page 47
Figure 3-23 LTC Connector Pin A rrangement (Small Platform)
Page
ND-46550 (E) CHAPTER 3 Page 49
LEN
LT03LT 02LT 01SLOT No.
MDF via the backplane (LTC cables).
Note 4: When DAIC is mounted in slot LT07, slot LT06 must use 4-port Line/Trunk card.
When opposite DAIA card is set to FP No.2:
LT0 6LT05LT04 LT 08LT0 7
LT0 0
CHAPTER 3 ND-46550 (E) Page 50
Figure 3-26 LTC Connector Pin Arrangement (1000 IVS)
Page
CHAPTER 3 ND-46550 (E) Page 52
Figure 3-28 Location of Each LEN (PIM N_UB)
Note: A maximum of 60 line/trunks can be accommodated in one Remote PIM.
ND-46550 (E) CHAPTER 3 Page 53
Figure 3-29 LTC Connector Pin Arrangement (PIM B - UB)
Page
ND-46550 (E) CHAPTER 3 Page 55
Figure 3-31 MDF Cross Connection for PFT (PN-AUCA)
CHAPTER 3 ND-46550 (E) Page 56
Note
ations from Central Office to the PBX; line quality cannot be assured.
Page
Page
ND-46550 (E) CHAPTER 3 Page 59
Figure 3-35 PFT Connector Pin Assignment
CHAPTER 3 ND-46550 (E) Page 60
Figure 3-36 MDF Cross Connection for PFT (PZ-8PFTA)
ND-46550 (E) CHAPTER 3 Page 61
Figure 3-36 MDF Cross Connection for PFT (PZ-8PFTA) (Continued)
Page
ND-46550 (E) CHAPTER 3 Page 63
Figure 3-38 Example of DTI Cable Connection vi a LTC Connector
CHAPTER 3 ND-46550 (E) Page 64
between the Main PIM and the Remote PIM.
Note 2: When the DAIA card is mounted in the MP/FP slot, be sure to connect the cable to the CN con-
nector on the DAIA card.
/
ND-46550 (E) CHAPTER 3 Page 65
1312 ft. (400 m) between the Main PIM and the Remote PIM.
Page
CHAPTER 4 TROUBLESHOOTING