Rear Panel, LAN 1,2,3,4 | NetComm NB712 manual

4.2Rear Panel

The rear panel of the SHDSL router is where all of the cable connections are made.

Connectors	Description
DC-IN	Power adaptor inlet: Input voltage 9VDC
LAN (1,2,3,4)	10/100BaseT auto-sensing and auto- MDIX for LAN port
	(RJ-45)
CONSOLE	RS-232C (DB9) for system conﬁguration and maintenance
LINE	SHDSL interface for WAN port (RJ-11)
RST	Reset button to reboot or load factory default
The reset button can be used in one of two ways.

(1)Press the Reset Button for one second to reboot the system only.

(2)Pressing the Reset Button for four seconds will cause the product to reload the factory default settings, thereby losing all of your settings. If you forget your user name or password, or if the router is having difﬁculties connecting to the Internet, you may want to reconﬁgure it to clear all previous settings. Press the Reset Button and hold for four (4) seconds with a paper clip or sharp pen/pencil.

NB712 /	NB714 User Guide	15
YML829	Rev1

Image 15

NetComm NB712 manual Rear Panel, LAN 1,2,3,4

Contents

Page Contents NB714 User Guide Features Package ContentsIntroduction Security SpeciﬁcationRouting Bridging WAN Interface IndicatorsATM QoS AAL5 Encapsulation Product Information ApplicationPhysical/Electrical Memory Firewall Types of Firewall Packet FilteringThere are three types of ﬁrewall Denial of Service Attack Circuit GatewayApplication Gateway UDP Flood Ping of deathSYN Flood Icmp Flood Frame Speciﬁcation Vlan Virtual Local Area Network VID uniquely identiﬁes the Vlan to which the frame belongs Applications Getting to know the router Front PanelLED status LAN 1,2,3,4 Rear Panel Check the Ethernet Adapter in PC Connecting your G.SHDSL Modem RouterCheck the Terminal Access Program Determine Connection Setting Bridge EoA Route EoA IPoA PPPoA Port router with network topology Install the Shdsl RouterPPPoE Cross-over Ethernet cables can be used Conﬁguration via Web Browser Router, which will lose any previous conﬁguration Basic Setup System error or disconnectionClick Basic for basic installation Bridge Mode LAN ParametersEnter Host Name Enter VPI Enter VCI Click LLC Click Next WAN1 Parameters Routing Mode Click Next to setup WAN1 parameters Dhcp ClientLAN IP Type Subnet Mask Dhcp ServerIP type IP Address DNS Server Trigger Dhcp Service Relay Dhcp relay For more information, refer to the section on NAT/DMZ PPPoE or PPPoAAAL5 Encap Protocol Idle Time PasswordPassword Conﬁrm Username Eprom Gateway IPoA or EoA Eprom Advanced Setup Data Rate Annex TypeLink Type Data rate Reconnect for better line connection Shdsl SNR marginMargin range is from 0 to Margin, the better the line connection WAN PCR Peak Cell Rate in kbps QoS Quality of ServiceUBR Unspeciﬁed Bit Rate CBR Constant Bit Rate Bridge Eprom Vlan Packets Pvid Press Modify RIP ModeRoute Auto RIP Summary Authentication required RIP VersionPoison Reverse NAT/DMZ Count Global Start IP Address Multi-DMZMulti-NAT Virtual Start IP Address Virtual Server Basic Firewall Security Firewall Automatic Firewall Security Connections and will be unresponsive Advanced Firewall SecurityClick Advanced Firewall Security and then press Finish SYN Attack Ping of death attack attempts to crash your system by Addresses originating from your network Dest. IP Address DirectionDescription Src. IP Address Filtering rule will be conﬁgured as follow Filtering Rule for Smtp connection Filtering Result Update Filtering Rule When the rule is ordered as ABC Rule Order10.0.0.0 172.16.6.0 Permit 10.1.99.0 172.16.0.0 Deny Any IP QoS NB714 User Guide Administration Security NB712 / NB714 User Guide MIB Snmp Community Snmp status Version Community Click on Time Sync Time Sync Sntp service Time ServerTime Zone Utility System Info Lose all the conﬁgured parameters Restore ConﬁgurationBackup Conﬁguration 10.2 Conﬁg Tool Upgrade To logout the router, press logout Logout Restart You can monitor the following Status LAN-to-LAN connection with bridge Mode CO sideLAN Parameters Enter VPI Enter VCI Encap WAN1 ParametersEnter IP 192.168.1.1 Enter Subnet Mask Enter Gateway 192.168.1.1 Enter Host Name CPE Side Host Name Enter SohoVCI32 EncapLLC IP Address 192.168.20.1 Subnet Mask 255.255.255.0 Host Name LAN to LAN Connection with Routing ModeDhcp Service Click Route and CO Side then press Next WAN Parameters Click Next to setup the IP parameters IP Address 192.168.10.1 Subnet Mask 255.255.255.0 Host Name Click Route and CPE Side then press Next 192.168.30.2 Baudrate 9600 Data Bits Parity Check Stop Bits Flow-control Useradmin PasswordSerial Console Telnet Operation Interface Window structure Menu Driven Interface Commands To choose another parametersCtrl + C To quit the conﬁguring item Ctrl + Q For help Menu Tree 14.7 Conﬁguration Exit Quit system Ping Packet internet groper command AdminDone via utility command Utility Status Script ShowSystem Conﬁg Ping RebootAdministration Write User Proﬁle Edit Community Entry List Show Snmp Supervisor Password and ID Move the cursor to timeserver1 and press enter Move the cursor to service and press enterSntp Move the cursor to sntp and press enter Move the cursor to list and review the setting Mode SetupUtility Exit Shdsl 14.16.3 WAN After enter add menu, the screen will prompt as follow Bridge Move the cursor to vlan and press enter Vlan 14.16.6 802.11Q Vlan Follow the following steps to conﬁgure 802.11q VlanFor each VLAN, Vlan ID is a unique number among 1~4095 Screen will display the following Generic command can setup RIP mode and auto summery modeYou can review the list of RIP parameters via list command Route IP share 14.16.8 LAN You can conﬁgure NAT parameters in nat menu 14.16.10 NAT Mapping After key in enter, the screen will prompt as below 14.16.11 PAT Firewall You can enable the demilitarized zone via active commandﬁrewall security level can conﬁgure via level command 14.16.12 DMZ Active DoS Protection IPQoS Dhcp You can view the Dhcp conﬁguration via list command Default DNS proxyHost name 100Mbps Appendix a Cable InformationRJ-45 Network Ports 10Mbps Straight and crossover cable conﬁguration Straight-Through CablingCross-Over Cabling TxD Shdsl Line Connector Console CableNo connection RxD O Contact Information Appendix B Registration and Warranty Information Product Warranty