Eprom | NetComm NB712 specs

The screen will display the parameters that will be written to EPROM. Check the parameters before writing to

EPROM.

Press Restart to restart the router with the new parameters or press Continue to setup other parameters.

NB712 /	NB714 User Guide	33
YML829	Rev1

Image 33

NetComm NB712 manual Eprom

Contents

Page Contents NB714 User Guide Features Package ContentsIntroduction Routing SpeciﬁcationBridging Security ATM QoS IndicatorsAAL5 Encapsulation WAN Interface Physical/Electrical ApplicationMemory Product Information Firewall Types of Firewall Packet FilteringThere are three types of ﬁrewall Denial of Service Attack Circuit GatewayApplication Gateway SYN Flood Ping of deathIcmp Flood UDP Flood Frame Speciﬁcation Vlan Virtual Local Area Network VID uniquely identiﬁes the Vlan to which the frame belongs Applications Getting to know the router Front PanelLED status LAN 1,2,3,4 Rear Panel Check the Terminal Access Program Connecting your G.SHDSL Modem RouterDetermine Connection Setting Check the Ethernet Adapter in PC Bridge EoA Route EoA IPoA PPPoA PPPoE Install the Shdsl RouterCross-over Ethernet cables can be used Port router with network topology Conﬁguration via Web Browser Router, which will lose any previous conﬁguration Basic Setup System error or disconnectionClick Basic for basic installation Bridge Mode LAN ParametersEnter Host Name Enter VPI Enter VCI Click LLC Click Next WAN1 Parameters Routing Mode Click Next to setup WAN1 parameters Dhcp ClientLAN IP Type IP type Dhcp ServerIP Address Subnet Mask DNS Server Trigger Dhcp Service Relay Dhcp relay AAL5 Encap PPPoE or PPPoAProtocol For more information, refer to the section on NAT/DMZ Password Conﬁrm PasswordUsername Idle Time Eprom Gateway IPoA or EoA Eprom Advanced Setup Link Type Annex TypeData rate Data Rate Margin range is from 0 to Shdsl SNR marginMargin, the better the line connection Reconnect for better line connection WAN UBR Unspeciﬁed Bit Rate QoS Quality of ServiceCBR Constant Bit Rate PCR Peak Cell Rate in kbps Bridge Eprom Vlan Packets Pvid Route RIP ModeAuto RIP Summary Press Modify Authentication required RIP VersionPoison Reverse NAT/DMZ Multi-NAT Multi-DMZVirtual Start IP Address Count Global Start IP Address Virtual Server Basic Firewall Security Firewall Automatic Firewall Security Click Advanced Firewall Security and then press Finish Advanced Firewall SecuritySYN Attack Connections and will be unresponsive Ping of death attack attempts to crash your system by Addresses originating from your network Description DirectionSrc. IP Address Dest. IP Address Filtering rule will be conﬁgured as follow Filtering Rule for Smtp connection Filtering Result Update Filtering Rule When the rule is ordered as ABC Rule Order10.0.0.0 172.16.6.0 Permit 10.1.99.0 172.16.0.0 Deny Any IP QoS NB714 User Guide Administration Security NB712 / NB714 User Guide MIB Snmp Community Snmp status Version Community Click on Time Sync Time Sync Sntp service Time ServerTime Zone Utility System Info Backup Conﬁguration Restore Conﬁguration10.2 Conﬁg Tool Lose all the conﬁgured parameters Upgrade To logout the router, press logout Logout Restart You can monitor the following Status LAN-to-LAN connection with bridge Mode CO sideLAN Parameters Enter IP 192.168.1.1 Enter Subnet Mask WAN1 ParametersEnter Gateway 192.168.1.1 Enter Host Name Enter VPI Enter VCI Encap CPE Side Host Name Enter SohoVCI32 EncapLLC Dhcp Service LAN to LAN Connection with Routing ModeClick Route and CO Side then press Next IP Address 192.168.20.1 Subnet Mask 255.255.255.0 Host Name WAN Parameters Click Next to setup the IP parameters IP Address 192.168.10.1 Subnet Mask 255.255.255.0 Host Name Click Route and CPE Side then press Next 192.168.30.2 Serial Console Useradmin PasswordTelnet Baudrate 9600 Data Bits Parity Check Stop Bits Flow-control Operation Interface Window structure Menu Driven Interface Commands To choose another parametersCtrl + C To quit the conﬁguring item Ctrl + Q For help Menu Tree 14.7 Conﬁguration Done via utility command Ping Packet internet groper command AdminUtility Exit Quit system Status System ShowConﬁg Script Administration RebootWrite Ping User Proﬁle Edit Community Entry List Show Snmp Supervisor Password and ID Sntp Move the cursor to service and press enterMove the cursor to sntp and press enter Move the cursor to timeserver1 and press enter Move the cursor to list and review the setting Utility SetupExit Mode Shdsl 14.16.3 WAN After enter add menu, the screen will prompt as follow Bridge Move the cursor to vlan and press enter Vlan 14.16.6 802.11Q Vlan Follow the following steps to conﬁgure 802.11q VlanFor each VLAN, Vlan ID is a unique number among 1~4095 You can review the list of RIP parameters via list command Generic command can setup RIP mode and auto summery modeRoute Screen will display the following IP share 14.16.8 LAN You can conﬁgure NAT parameters in nat menu 14.16.10 NAT Mapping After key in enter, the screen will prompt as below 14.16.11 PAT ﬁrewall security level can conﬁgure via level command You can enable the demilitarized zone via active command14.16.12 DMZ Firewall Active DoS Protection IPQoS Dhcp You can view the Dhcp conﬁguration via list command Default DNS proxyHost name RJ-45 Network Ports Appendix a Cable Information10Mbps 100Mbps Straight and crossover cable conﬁguration Straight-Through CablingCross-Over Cabling No connection Shdsl Line Connector Console CableRxD O TxD Contact Information Appendix B Registration and Warranty Information Product Warranty