14.16.3 WAN | NetComm NB712 specification

14.16.3 WAN

The router supports up to 8 PVCs, private virtual circuits, and so you can setup up to 8 WANs; WAN1 to WAN8. Move the cursor “ >> “ to wan and press enter. To setup WAN1, type 1.

----------------------------------------------------------------------

Command: setup wan <1~8>

Message: Please input the following information.

Interface number <1~8>: 1

----------------------------------------------------------------------

>> protocol	Link type protocol
address	IP address and subnet mask
vpi_vci	Conﬁgure VPI/VCI value
encap	Conﬁgure encapsulation type
qos	Conﬁgure VC QoS
isp	Conﬁgure account name, password and idle time
ip_type	Conﬁgure IP type in PPPoA and PPPoE
list	WAN interface conﬁguration

There are four types of protocols, IPoA, EoA, PPPoA and PPPoE, which you can setup.

For dynamic IP of PPPoA and PPPoE, you do not need to setup the IP address and subnet mask.

There is an unique VPI and VCI value for Internet connection supported by ISP. The range of VIP is from 0 to 255 and VCI from 0 to 65535.

There are two types of encapsulation types, VC-Mux and LLC.

You can setup virtual circuit quality of service, VC QoS, using qos command. The product supports UBR, CBR, VBR-rt and VBR-nrt. The peak cell rate can be conﬁgured from 64kbps to 2400kbps. Move the cursor to qos and press enter.

>> class	Conﬁgure QoS class
pcr	Conﬁgure peak cell rate (kbps)
scr	Conﬁgure sustainable cell rate (kbps)
mbs	Conﬁgure max. burst size (cell)

ISP command can conﬁgure account name, password and idle time. Idle time can be from 0 minute to 300 minutes.

Most ISPs use dynamic IP for PPP connection but some will use static IP. Conﬁgure the IP type, dynamic or ﬁxed, via ip_type command.

You can review the WAN interface conﬁguration via the list command.

NB712 /	NB714 User Guide	97
YML829	Rev1

Image 97

NetComm NB712 manual 14.16.3 WAN

Contents

Page Contents NB714 User Guide Package Contents FeaturesIntroduction Routing SpeciﬁcationBridging Security ATM QoS IndicatorsAAL5 Encapsulation WAN Interface Physical/Electrical ApplicationMemory Product Information Firewall Packet Filtering Types of FirewallThere are three types of ﬁrewall Circuit Gateway Denial of Service AttackApplication Gateway SYN Flood Ping of deathIcmp Flood UDP Flood Frame Speciﬁcation Vlan Virtual Local Area Network VID uniquely identiﬁes the Vlan to which the frame belongs Applications Front Panel Getting to know the routerLED status LAN 1,2,3,4 Rear Panel Check the Terminal Access Program Connecting your G.SHDSL Modem RouterDetermine Connection Setting Check the Ethernet Adapter in PC Bridge EoA Route EoA IPoA PPPoA PPPoE Install the Shdsl RouterCross-over Ethernet cables can be used Port router with network topology Conﬁguration via Web Browser Router, which will lose any previous conﬁguration System error or disconnection Basic SetupClick Basic for basic installation LAN Parameters Bridge ModeEnter Host Name Enter VPI Enter VCI Click LLC Click Next WAN1 Parameters Routing Mode Dhcp Client Click Next to setup WAN1 parametersLAN IP Type IP type Dhcp ServerIP Address Subnet Mask DNS Server Trigger Dhcp Service Relay Dhcp relay AAL5 Encap PPPoE or PPPoAProtocol For more information, refer to the section on NAT/DMZ Password Conﬁrm PasswordUsername Idle Time Eprom Gateway IPoA or EoA Eprom Advanced Setup Link Type Annex TypeData rate Data Rate Margin range is from 0 to Shdsl SNR marginMargin, the better the line connection Reconnect for better line connection WAN UBR Unspeciﬁed Bit Rate QoS Quality of ServiceCBR Constant Bit Rate PCR Peak Cell Rate in kbps Bridge Eprom Vlan Packets Pvid Route RIP ModeAuto RIP Summary Press Modify RIP Version Authentication requiredPoison Reverse NAT/DMZ Multi-NAT Multi-DMZVirtual Start IP Address Count Global Start IP Address Virtual Server Basic Firewall Security Firewall Automatic Firewall Security Click Advanced Firewall Security and then press Finish Advanced Firewall SecuritySYN Attack Connections and will be unresponsive Ping of death attack attempts to crash your system by Addresses originating from your network Description DirectionSrc. IP Address Dest. IP Address Filtering rule will be conﬁgured as follow Filtering Rule for Smtp connection Filtering Result Update Filtering Rule Rule Order When the rule is ordered as ABC10.0.0.0 172.16.6.0 Permit 10.1.99.0 172.16.0.0 Deny Any IP QoS NB714 User Guide Administration Security NB712 / NB714 User Guide MIB Snmp Community Snmp status Version Community Click on Time Sync Time Sync Time Server Sntp serviceTime Zone Utility System Info Backup Conﬁguration Restore Conﬁguration10.2 Conﬁg Tool Lose all the conﬁgured parameters Upgrade To logout the router, press logout Logout Restart You can monitor the following Status CO side LAN-to-LAN connection with bridge ModeLAN Parameters Enter IP 192.168.1.1 Enter Subnet Mask WAN1 ParametersEnter Gateway 192.168.1.1 Enter Host Name Enter VPI Enter VCI Encap Host Name Enter Soho CPE SideVCI32 EncapLLC Dhcp Service LAN to LAN Connection with Routing ModeClick Route and CO Side then press Next IP Address 192.168.20.1 Subnet Mask 255.255.255.0 Host Name WAN Parameters Click Next to setup the IP parameters IP Address 192.168.10.1 Subnet Mask 255.255.255.0 Host Name Click Route and CPE Side then press Next 192.168.30.2 Serial Console Useradmin PasswordTelnet Baudrate 9600 Data Bits Parity Check Stop Bits Flow-control Operation Interface Window structure To choose another parameters Menu Driven Interface CommandsCtrl + C To quit the conﬁguring item Ctrl + Q For help Menu Tree 14.7 Conﬁguration Done via utility command Ping Packet internet groper command AdminUtility Exit Quit system Status System ShowConﬁg Script Administration RebootWrite Ping User Proﬁle Edit Community Entry List Show Snmp Supervisor Password and ID Sntp Move the cursor to service and press enterMove the cursor to sntp and press enter Move the cursor to timeserver1 and press enter Move the cursor to list and review the setting Utility SetupExit Mode Shdsl 14.16.3 WAN After enter add menu, the screen will prompt as follow Bridge Move the cursor to vlan and press enter Vlan Follow the following steps to conﬁgure 802.11q Vlan 14.16.6 802.11Q VlanFor each VLAN, Vlan ID is a unique number among 1~4095 You can review the list of RIP parameters via list command Generic command can setup RIP mode and auto summery modeRoute Screen will display the following IP share 14.16.8 LAN You can conﬁgure NAT parameters in nat menu 14.16.10 NAT Mapping After key in enter, the screen will prompt as below 14.16.11 PAT ﬁrewall security level can conﬁgure via level command You can enable the demilitarized zone via active command14.16.12 DMZ Firewall Active DoS Protection IPQoS Dhcp You can view the Dhcp conﬁguration via list command DNS proxy DefaultHost name RJ-45 Network Ports Appendix a Cable Information10Mbps 100Mbps Straight-Through Cabling Straight and crossover cable conﬁgurationCross-Over Cabling No connection Shdsl Line Connector Console CableRxD O TxD Contact Information Appendix B Registration and Warranty Information Product Warranty