WAN1 Parameters, Enter VPI Enter VCI Encap

Enter IP:	192.168.1.1
Enter Subnet Mask:	255.255.255.0
Enter Gateway:	192.168.1.1
Enter Host Name:	SOHO

WAN1 Parameters

Enter VPI:	0
Enter VCI:	32
Encap:	Click LLC

Click Next

The screen will display the conﬁgured parameters. Check the parameters and click Restart . The router will reboot with the new settings.

74	NB712 / NB714 User Guide
	YML829 Rev1

Page 74

Image 74

NetComm NB712 manual WAN1 Parameters, Enter IP 192.168.1.1 Enter Subnet Mask, Enter Gateway 192.168.1.1 Enter Host Name

Contents

Page Contents NB714 User Guide Introduction FeaturesPackage Contents Bridging SpeciﬁcationRouting Security AAL5 Encapsulation IndicatorsATM QoS WAN Interface Memory ApplicationPhysical/Electrical Product Information Firewall There are three types of ﬁrewall Types of FirewallPacket Filtering Application Gateway Denial of Service AttackCircuit Gateway Icmp Flood Ping of deathSYN Flood UDP Flood Vlan Virtual Local Area Network Frame Speciﬁcation Applications VID uniquely identiﬁes the Vlan to which the frame belongs LED status Getting to know the routerFront Panel Rear Panel LAN 1,2,3,4 Determine Connection Setting Connecting your G.SHDSL Modem RouterCheck the Terminal Access Program Check the Ethernet Adapter in PC Bridge EoA Route EoA IPoA PPPoA Cross-over Ethernet cables can be used Install the Shdsl RouterPPPoE Port router with network topology Conﬁguration via Web Browser Router, which will lose any previous conﬁguration Click Basic for basic installation Basic SetupSystem error or disconnection Enter Host Name Bridge ModeLAN Parameters WAN1 Parameters Enter VPI Enter VCI Click LLC Click Next Routing Mode LAN IP Type Click Next to setup WAN1 parametersDhcp Client IP Address Dhcp ServerIP type Subnet Mask Trigger Dhcp Service DNS Server Dhcp relay Relay Protocol PPPoE or PPPoAAAL5 Encap For more information, refer to the section on NAT/DMZ Username PasswordPassword Conﬁrm Idle Time Eprom IPoA or EoA Gateway Eprom Advanced Setup Data rate Annex TypeLink Type Data Rate Margin, the better the line connection Shdsl SNR marginMargin range is from 0 to Reconnect for better line connection WAN CBR Constant Bit Rate QoS Quality of ServiceUBR Unspeciﬁed Bit Rate PCR Peak Cell Rate in kbps Bridge Eprom Vlan Pvid Packets Auto RIP Summary RIP ModeRoute Press Modify Poison Reverse Authentication requiredRIP Version NAT/DMZ Virtual Start IP Address Multi-DMZMulti-NAT Count Global Start IP Address Virtual Server Firewall Basic Firewall Security Automatic Firewall Security SYN Attack Advanced Firewall SecurityClick Advanced Firewall Security and then press Finish Connections and will be unresponsive Addresses originating from your network Ping of death attack attempts to crash your system by Src. IP Address DirectionDescription Dest. IP Address Filtering Rule for Smtp connection Filtering rule will be conﬁgured as follow Update Filtering Rule Filtering Result 10.0.0.0 172.16.6.0 Permit 10.1.99.0 172.16.0.0 Deny Any When the rule is ordered as ABCRule Order IP QoS NB714 User Guide Administration Security NB712 / NB714 User Guide Snmp MIB Snmp status Community Version Community Time Sync Click on Time Sync Time Zone Sntp serviceTime Server Utility System Info 10.2 Conﬁg Tool Restore ConﬁgurationBackup Conﬁguration Lose all the conﬁgured parameters Upgrade Logout To logout the router, press logout Restart Status You can monitor the following LAN Parameters LAN-to-LAN connection with bridge ModeCO side Enter Gateway 192.168.1.1 Enter Host Name WAN1 ParametersEnter IP 192.168.1.1 Enter Subnet Mask Enter VPI Enter VCI Encap VCI32 EncapLLC CPE SideHost Name Enter Soho Click Route and CO Side then press Next LAN to LAN Connection with Routing ModeDhcp Service IP Address 192.168.20.1 Subnet Mask 255.255.255.0 Host Name Click Next to setup the IP parameters WAN Parameters Click Route and CPE Side then press Next IP Address 192.168.10.1 Subnet Mask 255.255.255.0 Host Name 192.168.30.2 Telnet Useradmin PasswordSerial Console Baudrate 9600 Data Bits Parity Check Stop Bits Flow-control Operation Interface Window structure Ctrl + C To quit the conﬁguring item Ctrl + Q For help Menu Driven Interface CommandsTo choose another parameters Menu Tree 14.7 Conﬁguration Utility Ping Packet internet groper command AdminDone via utility command Exit Quit system Status Conﬁg ShowSystem Script Write RebootAdministration Ping User Proﬁle Snmp Edit Community Entry List Show Supervisor Password and ID Move the cursor to sntp and press enter Move the cursor to service and press enterSntp Move the cursor to timeserver1 and press enter Move the cursor to list and review the setting Exit SetupUtility Mode Shdsl 14.16.3 WAN Bridge After enter add menu, the screen will prompt as follow Vlan Move the cursor to vlan and press enter For each VLAN, Vlan ID is a unique number among 1~4095 14.16.6 802.11Q VlanFollow the following steps to conﬁgure 802.11q Vlan Route Generic command can setup RIP mode and auto summery modeYou can review the list of RIP parameters via list command Screen will display the following 14.16.8 LAN IP share 14.16.10 NAT You can conﬁgure NAT parameters in nat menu Mapping 14.16.11 PAT After key in enter, the screen will prompt as below 14.16.12 DMZ You can enable the demilitarized zone via active commandﬁrewall security level can conﬁgure via level command Firewall Active DoS Protection IPQoS You can view the Dhcp conﬁguration via list command Dhcp Host name DefaultDNS proxy 10Mbps Appendix a Cable InformationRJ-45 Network Ports 100Mbps Cross-Over Cabling Straight and crossover cable conﬁgurationStraight-Through Cabling RxD O Shdsl Line Connector Console CableNo connection TxD Appendix B Registration and Warranty Information Contact Information Product Warranty

NetComm NB712 WAN1 Parameters, Enter IP 192.168.1.1 Enter Subnet Mask, Enter VPI Enter VCI Encap

Models: NB712

Enter IP:

192.168.1.1

Enter Subnet Mask:

Enter Gateway:

192.168.1.1

Enter Host Name:

WAN1 Parameters

Enter VPI:

Enter VCI:

Encap:

NB712 / NB714 User Guide