NETGEAR JNR1010V2, JWNR2000v5, JWNR2010v5, WNR2010, WNR2020, WNR614, WNR618 Factory Settings

Supplemental Information

76

N150 and N300 Wireless Routers

Factory Settings

You can return the router to its factory settings. Use the end of a paper clip or some other

similar object to press and hold the WPS/Reset button on the back panel of the router for at

least four seconds. The router resets, and returns to the factory settings that are shown in the

following table.

Table 4. Router factory default settings

Feature Default Behavior

Router login User login URL www.routerlogin.com or www.routerlogin.net

User name (case-sensitive) admin

Login password (case-sensitive) password

Internet

connection WAN MAC address Use default hardware address

WAN MTU size 1500

Port speed AutoSensing

Local area

network (LAN) LAN IP 192.168.1.1

Subnet mask 255.255.255.0

DHCP server Enabled

DHCP range 192.168.1.2 to 192.168.1.254

Time zone United States is Pacific Time; otherwise, varies by region

Time zone adjusted for daylight

saving time Disabled

Wireless Wireless communication Enabled

SSID name Preset. For information, see the product label.

Network key (password)

Broadcast SSID Enabled

Transmission speed Auto

Note: Maximum wireless signal rate derived from IEEE

Standard 802.11 specifications. Actual throughput varies.

Network conditions and environmental factors, including

volume of network traffic, building materials and

construction, and network overhead lower actual data

throughput rate.

Country/region United States in the US; otherwise, varies by region

RF channel Auto

Operating mode Up to 300 Mbps or up to 150Mbps for model JNR1010v2

Contents

Main N150 and N300 Wireless Routers User Manual Models: Page Contents Chapter 1 Hardware Setup Chapter 2 Connect to the Network and Access the Router Chapter 3 Specify Your Internet Settings Chapter 4 Networking Chapter 5 Manage Your Network Chapter 6 Troubleshooting Page Page Hardware Setup N150 and N300 Wireless Routers Hardware Features Front Panel LEDs The router front panel has the following status LEDs. Table 1. Front panel LED descriptions Back Panel Position Your Router Cable Your Router Verify the Cabling Page Connect to the Network Wired Connection WiFi Connection Types of Logins Use a Web Browser to Access the Router NETGEAR genie Automatic Internet Setup Log In to the Router Page Page Use the Internet Setup Wizard Manually Set Up the Internet Connection Specify an Internet Connection Without a Login Specify an Internet Connection That Uses a Login Page Change the MTU Size Page Page Page View or Change WAN Settings Set Up a Default DMZ Server Change the Routers Device Name Change the LAN TCP/IP Settings Page Specify the IP Addresses that the Router Assigns Disable the DHCP Server Feature in the Router Reserve LAN IP Addresses Page Use the WPS Wizard for WiFi Connections Specify Basic WiFi Settings Page Change the WiFi Security Option Set Up a Guest Network Control the Wireless Radio Enable or Disable the Wireless Radio Set Up a Wireless Schedule Set up a Wireless Access List Page Specify WPS Settings Wireless Distribution System Set Up the Base Station Set Up a Repeater Page Static Routes Page View Devices Currently on the Network Improve Network Connections with Universal Plug and Play Page Page Update the Router Firmware Change the admin Password Recover the admin Password Page View Router Status View the Internet Connection Settings Display Internet Port Statistics View the Internet Connection Status DHCP Connection PPPoE Connection PPTP Connection View Wireless Settings View Guest Network Settings Reboot the Router Manage the Configuration File Back Up Settings Restore Configuration Settings Erase Configuration Settings Page Forgotten Passwords admin Password WiFi Passwords WiFi Connections Changes Not Saved Troubleshoot with the LEDs Apply Power to the Router and Check the LEDs All LEDs Remain Lit Power LED Is Off or Blinking Power LED Stays Amber Internet LEDs Is Off WiFi LED Is Off Cannot Log In to the Router The Router Cannot Access the Internet Troubleshoot Internet Browsing Troubleshoot a PPPoE Internet Connection Troubleshoot Your Network Using the Ping Utility Test the LAN Path to Your Router Test the Path from Your Computer to a Remote Device Troubleshoot IP Addresses Page Supplemental Information N150 and N300 Wireless Routers Factory Settings Table 4. Router factory default settings Supplemental Information N150 and N300 Wireless Routers Technical Specifications Table 5. Router specifications Table 4. Router factory default settings (continued)