Configuring the MultiZone receiver
The Niles
NOTE: THE master unit, THE SLAVE unit (IF APPLICABLE), ALL SOURCE COMPONENTS, KEYPADS AND SPEAKERS MUST BE CONNECTED PRIOR TO PERFORMING ANY OF THESE OPERATIONS.
Main Power
The
Configuration Mode
To enter configuration mode, power down the
R E L E A S E B U T T O N S
T O C O N T I N U E
[ MASTER ] will be on the display. If you have two
M A S T E R
Master/Slave
On the
| M | A | S | T | E | R |
|
|
|
|
|
|
|
|
|
|
|
|
| S | L | A | V | E |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
To continue to the next system configuration Zone Linking, press the Set key once. To save your settings and to exit the configuration mode, simultaneously hold down the Band and Set keys. [ RELEASE BUTTONS TO CONTINUE ] appears on the display. The
NOTE: All external IR or
18
connected to the Master and not to the Slave. IR from the keypads connected to the Slave chassis will be routed to the Master chassis via the expansion connection port.
Zone Linking
This feature allows two or more zones to always play the same source at the same time. Linked zones will
Note: only one Zone Linking group may be created per unit (one for the Master, one for the Slave).
While in the configuration mode (see above). Press the Set Key until [ 1234 LINKING MASTER ] shows in the display.
| 1 | 2 | 3 | 4 |
|
|
|
|
| L | I | N | K | I | N | G |
|
|
|
|
|
|
|
|
|
|
|
| M | A | S | T | E | R |
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
A cursor will be blinking under the number “1.”
Press the + key to toggle between the zones. The cursor blinks under the zone number when it is highlighted. Press the Band key to make a highlighted zone a linked zone. [ L ] will appear below that zone number.
| 1 | 2 | 3 | 4 |
|
|
|
|
| L | I | N | K | I | N | G |
|
| L |
|
|
|
|
|
|
|
|
| M | A | S | T | E | R |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Once you reach “4” it will toggle back to “1” on the Slave. Once you have reached “4” on the Slave it will toggle back to “1” on the Master.
| 1 | 2 | 3 | 4 |
|
|
|
|
| L | I | N | K | I | N | G |
|
| L |
| L |
|
|
|
|
|
|
| M | A | S | T | E | R |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Repeat these steps until all of the desired zones have been linked.
To continue to the next system configuration Paging, press the Set key once. To save your settings and to exit the configuration mode, simultaneously hold down the Band and Set keys. [ RELEASE BUTTONS TO CONTINUE ] appears on the display. The
R E L E A S E B U T T O N S
T O C O N T I N U E
Paging
By default, all zones will respond to a page when it is input to the paging port. When a signal is detected, the selected zones will switch
NILES AUDIO CORPORATION –