M p e r a t u r e, K e U p R m a l T e | Nilfisk-ALTO 3.4 specs

c.Temperature

Used to key in the value of the environmental temperature of place of installation.

The system uses this value to automatically compensate for the differentials due to the difference speed of sound Transmission according to the air temperature.

This allows to set the delays during the sound-check and only have to reset them automatically when necessary (For example during a concert, in the event of big jumps in temperature, etc.).

The editing values are in the following ranges: +60 C ~ -30 C with 1 C steps

140.0 F ~ -22.0 F with 1.8 F steps

T e m p e r a t u r e

2 0 C

T e m p e r a t u r e

6 8 . 0 F

Note: the measurement units can be chosen between C (degrees Centigrade) and F (degrees Fahrenheit) by means of the Temperature Unit function (UTILITY menu - Units submenu).

d. Wake Up

Allows to choose the mode in which MUTE functions are restored when the MAXIDRIVE3.4 is switched on.

The options include:

Normal	Mute
when switched on, the system restores the last	when switched on, the system automatically
MUTE configuration before switching off	sets all the outputs in MUTE

W a k e U p

N o r m a l

W a k e U p

M u t e

e. LCD Contrast

Allows to adjust the Display contrast.

The values are in the following range: 0 (minimum contrast) ~ 32 (maximum contrast).

L C D C o n t r a s t

2 6

5.4.4LOCK SUBMENU

Used to enable or disable the protection of the system against accidental or unauthorized changes.

Lock

Lock

27

Image 28

Nilfisk-ALTO 3.4 user manual M p e r a t u r e, K e U p R m a l T e, D C o n t r a s t, Lock Submenu

Contents

MAXIDRIVE3.4 Safety Related Symbols Important Safety InstructionsPower Supply External Connection Preface Table of Contents Introduction Rear Panel Configuration of the system Getting StartedOutputs Inputs 3 5 B 2 4 2 x 3 W Adjusting the input signal 3 B 2 4 S 5 2 x 2 W + 2 M aA d P r e s e t 2 x 3 W P u t I n First Setup System configuration 3 B 2 4 S 5 2 x 2 W + 2 M aA G a I N D B A & B G a I N Number Of Presets 3 B 2 4 S 5 2 x 2 W + 2 M a Type of Preset 3 B 2 4 S 5 2 x 2 W + 2 M aName of the Preset 3 B 2 4 S 5 2 x 2 W + 2 M a Example Preset Modifications 1 3 B 2 4 S 5 2 x 2 W + 2 M a Menu MAP Configuration DescriptionPreset Menu System Protection 3 B 2 4 S 5 2 x 2 W + 2 M a C a R D Store & Naming Preset O r e P r e s e t 2 x 2 W + 2 M aO r e P r e s e t O p e r a H a l l E s e t N a m i n W + 2 M a T P r e s e t 2 W + 2 M a Dump Out PresetIncoming Dump C o m i n g D u m p N o r e C e p t Delay Menu P u t D e l a y L a YM S T p u t Edit menu 2 u SInput Gain I N D BP u t Input EQ Bandwidth Centre Frequency / Cutoff FrequencyGain R u V e r0 0 H z Phase F B e s 24 6 H z Crossover frequency Output EQ Output GainEditing values are between +6dB ~ -30dB, with 0.5dB steps Output Pol R m a L a R I T YV e r s e Utility Menu Ganging Submenu P u t G a n g i n g N g i n gInput Ganging T p u t G a n g i n g M . T h r e s h . U n i tM P e r a t u r e U n i t Units Submenu P u t S e l e c t G i t a l A l o g T u pT p u t M e t e r s E M u t e S t M u t e M p e r a t u r e K e U p R m a l T eD C o n t r a s t Lock Submenu 2 2 W + 2 M a 3 B 2 4 S 5 C kTotal Partial A 1 3 B 2 4 S 5 2 2 W + 2 M a L O C KS s w o r d S s w o r d R D COMM. Setup Submenu R m a t R dR m a t C a r d R m a t t i n g R m a t D o n e M m . S e t u p Inputs a & B, Digital IN, RS485 ConnectionsInputs a & B Factory Preset Configuration Outputs 1 ~ 6, RS485 OUTRS232 Special attentions for RS232 interface Signal Power Organization MAXIDRIVE3.4 Audio Mixer Signal PowerA135 B246 3-WAY Stereo 2X2W Signal Power Audio Mixer High Left High Right A1324 S56 4-WAY4 Mono + 2 Mono AUX 4W+2MAX Communications PC & one or more MAXIDRIVE3.4 connection To / from RS232 Technical Specifications Return Notice Warranty Registration CardTerms and Conditions Seikaku Technical Group Limited