Connections, Inputs a & B, Digital IN, RS485 | Nilfisk-ALTO 3.4

The PRESET Change command is completely identical to MIDI Program Change: the transmitting unit sends an instruction containing a number of PRESETS to load; the receiving units (if they are able to accept the com- mand) each loads into its own memory the PRESET with the corresponding number.

This means that, in a chain of MAXIDRIVE3.4, all the units set with PRESET Change RX = Accept load the same number of PRESET, in spite of the fact that it corresponds to PRESETS with different contents in the various units.

Note: the PRESET Dump function is used to transmit the same contents.

MAXIDRIVE3.4 #1

Load Preset

SEND

..

Preset #2

Preset #3

Preset #4

Preset #5

Preset #6

Preset #7

Preset #8

Preset #9

..

PORT

SERIAL

MAXIDRIVE3.4 #2

Preset Change RX

ACCEPT

..

#2 MySetup

#3 MySetup5

#4 LiveSet1

#5 LiveSet2

#6 Monitor

#7 Monitor2

#8 Monitor3

#9 Side

..

PORT

SERIAL

MAXIDRIVE3.4 #3

Preset Change RX

IGNORE

..

#2 SideField

#3 Concert1

#4 Concert2

#5 Concert3

#6 Concert4

#7 Remote1

#8 Remote2

#9 Remote2

..

6.CONNECTIONS

The following diagrams show the schemes of the recommended cables and some connection examples referred to various system configurations.

Inputs A & B, Digital IN, RS485 IN

	1	GROUND
3		GROUND
3

BALANCED XLR-M

2	COLD (		)	HOT (+)
	COLD (		)

Inputs A & B

SLEEVE

TIP

BALANCED JACK

GROUND

RING	COLD (		)	HOT (+)

31

Image 32

Nilfisk-ALTO 3.4 user manual Connections, Inputs a & B, Digital IN, RS485

Contents

MAXIDRIVE3.4 Safety Related Symbols Important Safety InstructionsPower Supply External Connection Preface Table of Contents Introduction Rear Panel Configuration of the system Getting StartedOutputs Inputs 3 5 B 2 4 2 x 3 W Adjusting the input signal 3 B 2 4 S 5 2 x 2 W + 2 M aA d P r e s e t 2 x 3 W P u t I n First Setup System configuration 3 B 2 4 S 5 2 x 2 W + 2 M aA G a I N D B A & B G a I N Number Of Presets 3 B 2 4 S 5 2 x 2 W + 2 M a Type of Preset 3 B 2 4 S 5 2 x 2 W + 2 M aName of the Preset 3 B 2 4 S 5 2 x 2 W + 2 M a Example Preset Modifications 1 3 B 2 4 S 5 2 x 2 W + 2 M a Menu MAP Configuration DescriptionPreset Menu System Protection 3 B 2 4 S 5 2 x 2 W + 2 M a C a R D Store & Naming Preset O r e P r e s e t 2 x 2 W + 2 M aO r e P r e s e t O p e r a H a l l E s e t N a m i n W + 2 M a Incoming Dump Dump Out PresetT P r e s e t 2 W + 2 M a C o m i n g D u m p N o r e C e p t Delay Menu P u t D e l a y L a YM S T p u t Input Gain 2 u SEdit menu I N D BP u t Input EQ Gain Centre Frequency / Cutoff FrequencyBandwidth 0 0 H z V e rR u Phase F B e s 24 6 H z Crossover frequency Output EQ Output GainEditing values are between +6dB ~ -30dB, with 0.5dB steps Output Pol V e r s e L a R I T YR m a Utility Menu Ganging Submenu Input Ganging N g i n gP u t G a n g i n g T p u t G a n g i n g M . T h r e s h . U n i tM P e r a t u r e U n i t Units Submenu T p u t M e t e r s E M u t e S t M u t e T u pP u t S e l e c t G i t a l A l o g M p e r a t u r e K e U p R m a l T eD C o n t r a s t Lock Submenu Total Partial C k2 2 W + 2 M a 3 B 2 4 S 5 A 1 3 B 2 4 S 5 2 2 W + 2 M a L O C KS s w o r d S s w o r d R D COMM. Setup Submenu R m a t R dR m a t C a r d R m a t t i n g R m a t D o n e M m . S e t u p Inputs a & B ConnectionsInputs a & B, Digital IN, RS485 Factory Preset Configuration Outputs 1 ~ 6, RS485 OUTRS232 Special attentions for RS232 interface Signal Power Organization A135 B246 3-WAY Stereo 2X2W Audio Mixer Signal PowerMAXIDRIVE3.4 Signal Power Audio Mixer High Left High Right A1324 S56 4-WAY4 Mono + 2 Mono AUX 4W+2MAX Communications PC & one or more MAXIDRIVE3.4 connection To / from RS232 Technical Specifications Terms and Conditions Warranty Registration CardReturn Notice Seikaku Technical Group Limited