38 3G10WV Hspa Wi-Fi Router with Voice | NordicTrack specs

6.1.4Update Firmware

The following screen appears when selecting Update Firmware. By following this screens steps, you can update your Routers firmware. Manual device upgrades from a locally stored file can also be performed using the following screen.

1:Obtain an updated software image file

2:Enter the path and filename of the firmware image file in the Software File Name field or click the Browse button to locate the image file.

3:Click the Update Software button once to upload and install the file.

NOTE:	The update process will take about 2 minutes to complete. The Router will reboot and the browser window will refresh to the
	default screen upon successful installation.
	It is recommended that you compare the Software Version at the top of the Basic screen (WUI homepage) with the firmware
	version installed, to confirm the installation was successful.

38 – 3G10WV HSPA Wi-Fi Router with Voice

Image 38

NordicTrack manual 38 3G10WV Hspa Wi-Fi Router with Voice

Contents

3G10WV Hspa 7.2 Mbps Wi-Fi Router with Voice Important Notice and Safety Precaution Preface Table of Contents Appendix a Command Line Interface CLI Commands Via Telnet Introduction Introduction Features Package Contents Associated port LED IndicatorsColor Mode Description Rear Panel Quick Setup Configure the router through the Web User Interface WUI Quick SetupSetup Procedure Save the router configuration and reboot see section Web User Interface Default Settings Web User Interface Click OK to submit the settings TCP/IP SettingsDhcp Mode Login Procedure To login to the web interface, follow the steps below Web User Interface Homepage Basic / Home Following table provides further details Fields Description 3G Settings This menu includes 3G service Setup and PIN Configuration 3G Settings3G Service Setup 20 3G10WV Hspa Wi-Fi Router with Voice PIN Lock Off PIN ConfigurationPIN Code Protection PIN Lock On PIN Code Change Wireless Wireless Setup Option Description Click Save/Apply to configure the wireless security options Security WEP Encryption will also be enabled Card. If the Ssid does not match, access is deniedAuthentication Select Ssid Configuration AP Isolation Broadcast and multicast messages. The default isDefault is disabled Point can be linked Mbit/s Dsss specification as described in Ieee Std 54g ModeOnly mode 54g Protection MAC Address Deny Rejects access for the specified MAC addressesMAC Filter Can be added Feature Options Wireless BridgeClick Save/Apply to implement new configuration settings Is generated randomly Authorized Lists those devices with authorized accessStation Info Associated Management Device Settings Management Update Settings Restore Default 38 3G10WV Hspa Wi-Fi Router with Voice By default, Snmp agent is enabled on the gateway Configure Snmp agent on 3G10WVSetting up Snmp agent Press Save/Apply to activate setting Simple Network Time Protocol Sntp Access Control 42 3G10WV Hspa Wi-Fi Router with Voice Save and Reboot Advanced Setup Advanced Setup This chapter explains advanced setup for your Router Hosts connected to Hspa 7.2 Mbps Wi-Fi Router Setting. By default NAT is enabledThese options are used for special Dhcp set up Local Area Network LAN Show up on the same page as below Enable DhcpEnable Dhcp Server Server Relay Network Address Translation NAT Port Forwarding Options Description Is selected the port ranges are automatically configuredSelected the port ranges are automatically configured External Port End Port Triggering Trigger Protocol TCP, TCP/UDP or UDP Open Port Start Demilitarized DMZ HostTrigger Port End Open Port End 52 3G10WV Hspa Wi-Fi Router with Voice Options Description MAC address of the PC running the browser Parental ControlUser Name User-defined label for this restriction Routing 56 3G10WV Hspa Wi-Fi Router with Voice DNS Server Configuration Domain Name Servers DNS Dynamic DNS Options Descriptions Voice Configuring your 3G10WV for placing Voice Calls Voice Status Status Diagnostics Test Description System Log Click View System Log. The results are displayed as follows 3G Status Status Description Quality Ec/Io Status BCS Battery Charge LevelStatus Strongest cells Network Registration Statistics Interface Shows connection interfaces Service Shows the service type Field Description RouteSelect Route to display the paths the Router has found But may be needed by routing daemons Click ARP to display the ARP information Dynamic Host Configuration Protocol DhcpARP Click Dhcp to display the Dhcp information Ping CLI commands Via Telnet End the telnet session CLI commands via TelnetHelp Synopsis help ? Example Description Display the 3G network connection status Examples Sierra show --mode Wcdma L1 StateL1MFACH RRC State Cellfach RX level dBm-90Description Display the Imsi and Imei value Sierra show --hsdcat !HSDCAT Synopsis sierra set --apn profile apn profile 1 Custom APN Sierra show --mode mode UmtsExample Set the Custom APN to test.test Sierra show -auth 1 Profile1 PAP Synopsis sierra set --comp profile type enabledisableExample Enable the IP header compression for Custom APN PIN code configuration Connect / Disconnect PPP session Changed the PIN code successfully PUK code unlock Synopsis sierra show --PIN-LOCK ExampleSierra set --PIN-CHG 0000 Sierra set --PUK 11111111 0000 PUK unlock successfully Options Enable Wlan Valid value 32 characters string --country countryStr Description Set the wireless LAN channel Valid value 0~14Means auto select channel. Default value Default value 0 --mrate rateVal Default value 2346 --dtim dtimInterval Default value long Example Options Example Remove MACaddress Options Configure wireless LAN MAC filterSynopsis Description add one MAC Address entry --remove MACaddress Description set remote bridge MAC address Advance Wlan security wpaGTKRekey = Wlan security WepCurrentKeyindex = 1 --macfilter 92 3G10WV Hspa Wi-Fi Router with Voice Wlan info --config --security --macfilter --wds --station Scenario 6 to configure AP with WPA2 security 3G10WV Hspa Wi-Fi Router with Voice Contact Information