LED Indicators, Color Mode Description | NordicTrack 3G10WV specs

1.3LED Indicators

The front panel LED indicators are shown in this illustration and followed by detailed explanations in the table below.

3G10WV

HSPA Wi-Fi Router with Voice

								t
Power	Phone	LAN	1	LAN	2	-Fi	Inter	ne	2G
Power	Phone	LAN		LAN		Wi	Inter	3G	2G

Signal Strength

Lo	Med	High
w

LED		Color	Mode	Description

POWER		Green	On	Power on

			Off	Power off

Phone		Green	On	Phone line active

			Off	Phone line inactive or not connected

LAN 1~4		Green	On	Powered device connected to the associated port (includes devices with wake-on-LAN
				capability where a slight voltage is supplied to an Ethernet connection)

			Off	No activity, modem powered off, no cable or no powered device connected to the
				associated port

			Blink	LAN activity present (traffic in either direction)

Wi-Fi		Green	On	The wireless module is ready.

			Off	The wireless module is not installed.

			Blink	Data being transmitted or received over Wi-Fi.

Internet		Green	Blink	Data is transmitted through Internet connection

			Off	No connection to the internet or router powered off

			On	Internet connection established

3G		Green	On	Internet connection established.

			Blink	Connecting with UMTS cellular station

			Off	No connection with UMTS cellular station, no activity or router powered off.

2G		Green	On	Internet connection established.

			Blink	Connecting to an EDGE, GPRS or GSM cellular station

			Off	No connection with EDGE, GPRS or GSM cellular station, no activity or router powered off.

Low		Green	On	Low signal strength

			Off	No activity, router powered off or on other signal strength

Med		Green	On	Medium signal strength

			Off	No activity, router powered off or on other signal strength

High		Green	On	High signal strength

			Off	No activity, router powered off or on other signal strength
NOTE:	The six LEDs on the right side of the front panel display (Internet, 3G, 2G, Low, Med, High) will cycle on and off if PIN code protection is
	activated. In this case, you should consult section 4.2.1 PIN Code Protection (page 21) for further instructions.

–3G10WV HSPA Wi-Fi Router with Voice

Image 8

NordicTrack 3G10WV manual LED Indicators, Color Mode Description, Associated port

Contents

3G10WV Hspa 7.2 Mbps Wi-Fi Router with Voice Important Notice and Safety Precaution Preface Table of Contents Appendix a Command Line Interface CLI Commands Via Telnet Introduction Introduction Features Package Contents Associated port LED IndicatorsColor Mode Description Rear Panel Quick Setup Quick Setup Setup ProcedureConfigure the router through the Web User Interface WUI Save the router configuration and reboot see section Web User Interface Default Settings Web User Interface Click OK to submit the settings TCP/IP SettingsDhcp Mode Login Procedure To login to the web interface, follow the steps below Web User Interface Homepage Basic / Home Following table provides further details Fields Description 3G Settings This menu includes 3G service Setup and PIN Configuration 3G Settings3G Service Setup 20 3G10WV Hspa Wi-Fi Router with Voice PIN Lock Off PIN ConfigurationPIN Code Protection PIN Lock On PIN Code Change Wireless Wireless Setup Option Description Click Save/Apply to configure the wireless security options Security Card. If the Ssid does not match, access is denied AuthenticationWEP Encryption will also be enabled Select Ssid Configuration Broadcast and multicast messages. The default is Default is disabledAP Isolation Point can be linked 54g Mode Only modeMbit/s Dsss specification as described in Ieee Std 54g Protection Deny Rejects access for the specified MAC addresses MAC FilterMAC Address Can be added Feature Options Wireless BridgeClick Save/Apply to implement new configuration settings Authorized Lists those devices with authorized access Station InfoIs generated randomly Associated Management Device Settings Management Update Settings Restore Default 38 3G10WV Hspa Wi-Fi Router with Voice Configure Snmp agent on 3G10WV Setting up Snmp agentBy default, Snmp agent is enabled on the gateway Press Save/Apply to activate setting Simple Network Time Protocol Sntp Access Control 42 3G10WV Hspa Wi-Fi Router with Voice Save and Reboot Advanced Setup Advanced Setup This chapter explains advanced setup for your Router Setting. By default NAT is enabled These options are used for special Dhcp set upHosts connected to Hspa 7.2 Mbps Wi-Fi Router Local Area Network LAN Enable Dhcp Enable Dhcp ServerShow up on the same page as below Server Relay Network Address Translation NAT Port Forwarding Is selected the port ranges are automatically configured Selected the port ranges are automatically configuredOptions Description External Port End Port Triggering Demilitarized DMZ Host Trigger Port EndTrigger Protocol TCP, TCP/UDP or UDP Open Port Start Open Port End 52 3G10WV Hspa Wi-Fi Router with Voice Options Description MAC address of the PC running the browser Parental ControlUser Name User-defined label for this restriction Routing 56 3G10WV Hspa Wi-Fi Router with Voice DNS Server Configuration Domain Name Servers DNS Dynamic DNS Options Descriptions Voice Configuring your 3G10WV for placing Voice Calls Voice Status Status Diagnostics Test Description System Log Click View System Log. The results are displayed as follows 3G Status Status Description Status BCS Battery Charge Level StatusQuality Ec/Io Strongest cells Network Registration Statistics Interface Shows connection interfaces Service Shows the service type Route Select Route to display the paths the Router has foundField Description But may be needed by routing daemons Dynamic Host Configuration Protocol Dhcp ARPClick ARP to display the ARP information Click Dhcp to display the Dhcp information Ping CLI commands Via Telnet CLI commands via Telnet HelpEnd the telnet session Synopsis help ? Example Description Display the 3G network connection status Examples Wcdma L1 StateL1MFACH RRC State Cellfach RX level dBm-90 Description Display the Imsi and Imei valueSierra show --mode Sierra show --hsdcat !HSDCAT Synopsis sierra set --apn profile apn profile 1 Custom APN Sierra show --mode mode UmtsExample Set the Custom APN to test.test Sierra show -auth 1 Profile1 PAP Synopsis sierra set --comp profile type enabledisableExample Enable the IP header compression for Custom APN PIN code configuration Connect / Disconnect PPP session Synopsis sierra show --PIN-LOCK Example Sierra set --PIN-CHG 0000Changed the PIN code successfully PUK code unlock Sierra set --PUK 11111111 0000 PUK unlock successfully Options Enable Wlan Valid value 32 characters string --country countryStr Description Set the wireless LAN channel Valid value 0~14Means auto select channel. Default value Default value 0 --mrate rateVal Default value 2346 --dtim dtimInterval Default value long Example Options Example Configure wireless LAN MAC filter SynopsisRemove MACaddress Options Description add one MAC Address entry --remove MACaddress Description set remote bridge MAC address Advance Wlan security wpaGTKRekey = Wlan security WepCurrentKeyindex = 1 --macfilter 92 3G10WV Hspa Wi-Fi Router with Voice Wlan info --config --security --macfilter --wds --station Scenario 6 to configure AP with WPA2 security 3G10WV Hspa Wi-Fi Router with Voice Contact Information