Diagnostics, Test Description | NordicTrack 3G10WV specs

9.1Diagnostics

The Diagnostics menu provides feedback on the connection status of the device. The individual tests are listed below. If a test displays a fail status:

1:Click on the Help link

2:Now click Re-run Diagnostic Tests at the bottom of the screen to re-test and confirm the error

3:If the test continues to fail, follow the troubleshooting procedures in the Help screen.

Test	Description

ENET Connection	Pass: Indicates that the Ethernet interface from your computer is connected to the
	LAN port of this Router.
	Fail: Indicates that the Router does not detect the Ethernet interface on your
	computer.

Wireless connection	Pass: Indicates that the wireless card is ON.
	Down: Indicates that the wireless card is OFF.

Ping Default Gateway	Pass: Indicates that the Router can communicate with the first entry point to the
	network. It is usually the IP address of the ISP’s local Gateway.
	Fail: Indicates that the Router was unable to communicate with the first entry point
	on the network, and it may not have an effect on your Internet connectivity. If this test
	fails and you can access the Internet, there is no need to troubleshoot this issue.

Ping Primary Domain	Pass: Indicates that the Router can communicate with the primary Domain Name
Name Server	Server (DNS).
	Fail: Indicates that the Router was unable to communicate with the primary Domain
	Name Server (DNS). It may not have an effect on your Internet connectivity. Therefore
	if this test fails but you are still able to access the Internet, there is no need to
	troubleshoot this issue.

3G10WV HSPA Wi-Fi Router with Voice – 63

Image 63

NordicTrack 3G10WV manual Diagnostics, Test Description

Contents

3G10WV Hspa 7.2 Mbps Wi-Fi Router with Voice Preface Important Notice and Safety Precaution Table of Contents Appendix a Command Line Interface CLI Commands Via Telnet Introduction Introduction Package Contents Features LED Indicators Color Mode DescriptionAssociated port Rear Panel Quick Setup Save the router configuration and reboot see section Quick SetupSetup Procedure Configure the router through the Web User Interface WUI Web User Interface Web User Interface Default Settings TCP/IP Settings Dhcp ModeClick OK to submit the settings To login to the web interface, follow the steps below Login Procedure Basic / Home Web User Interface Homepage Fields Description Following table provides further details 3G Settings 3G Settings 3G Service SetupThis menu includes 3G service Setup and PIN Configuration 20 3G10WV Hspa Wi-Fi Router with Voice PIN Configuration PIN Code ProtectionPIN Lock Off PIN Lock On PIN Code Change Wireless Wireless Option Description Setup Security Click Save/Apply to configure the wireless security options Select Ssid Card. If the Ssid does not match, access is deniedAuthentication WEP Encryption will also be enabled Configuration Point can be linked Broadcast and multicast messages. The default isDefault is disabled AP Isolation 54g Protection 54g ModeOnly mode Mbit/s Dsss specification as described in Ieee Std Can be added Deny Rejects access for the specified MAC addressesMAC Filter MAC Address Wireless Bridge Click Save/Apply to implement new configuration settingsFeature Options Associated Authorized Lists those devices with authorized accessStation Info Is generated randomly Management Management Device Settings Restore Default Update Settings 38 3G10WV Hspa Wi-Fi Router with Voice Press Save/Apply to activate setting Configure Snmp agent on 3G10WVSetting up Snmp agent By default, Snmp agent is enabled on the gateway Simple Network Time Protocol Sntp Access Control 42 3G10WV Hspa Wi-Fi Router with Voice Save and Reboot Advanced Setup This chapter explains advanced setup for your Router Advanced Setup Local Area Network LAN Setting. By default NAT is enabledThese options are used for special Dhcp set up Hosts connected to Hspa 7.2 Mbps Wi-Fi Router Server Relay Enable DhcpEnable Dhcp Server Show up on the same page as below Port Forwarding Network Address Translation NAT External Port End Is selected the port ranges are automatically configuredSelected the port ranges are automatically configured Options Description Port Triggering Open Port End Demilitarized DMZ HostTrigger Port End Trigger Protocol TCP, TCP/UDP or UDP Open Port Start 52 3G10WV Hspa Wi-Fi Router with Voice Options Description Parental Control User Name User-defined label for this restrictionMAC address of the PC running the browser Routing 56 3G10WV Hspa Wi-Fi Router with Voice Domain Name Servers DNS DNS Server Configuration Options Descriptions Dynamic DNS Voice Voice Configuring your 3G10WV for placing Voice Calls Status Status Test Description Diagnostics System Log Click View System Log. The results are displayed as follows 3G Status Status Description Strongest cells Network Registration Status BCS Battery Charge LevelStatus Quality Ec/Io Interface Shows connection interfaces Statistics Service Shows the service type But may be needed by routing daemons RouteSelect Route to display the paths the Router has found Field Description Click Dhcp to display the Dhcp information Dynamic Host Configuration Protocol DhcpARP Click ARP to display the ARP information Ping CLI commands Via Telnet Synopsis help ? Example CLI commands via TelnetHelp End the telnet session Examples Description Display the 3G network connection status Sierra show --hsdcat !HSDCAT Wcdma L1 StateL1MFACH RRC State Cellfach RX level dBm-90Description Display the Imsi and Imei value Sierra show --mode Sierra show --mode mode Umts Example Set the Custom APN to test.testSynopsis sierra set --apn profile apn profile 1 Custom APN Synopsis sierra set --comp profile type enabledisable Example Enable the IP header compression for Custom APNSierra show -auth 1 Profile1 PAP Connect / Disconnect PPP session PIN code configuration Sierra set --PUK 11111111 0000 PUK unlock successfully Synopsis sierra show --PIN-LOCK ExampleSierra set --PIN-CHG 0000 Changed the PIN code successfully PUK code unlock Wlan Options Enable Description Set the wireless LAN channel Valid value 0~14 Means auto select channel. Default valueValid value 32 characters string --country countryStr Default value 2346 --dtim dtimInterval Default value 0 --mrate rateVal Example Default value long Options Example Description add one MAC Address entry --remove MACaddress Configure wireless LAN MAC filterSynopsis Remove MACaddress Options Description set remote bridge MAC address Wlan security wpaGTKRekey = Advance Wlan security WepCurrentKeyindex = 1 --macfilter 92 3G10WV Hspa Wi-Fi Router with Voice Wlan info --config --security --macfilter --wds --station Scenario 6 to configure AP with WPA2 security 3G10WV Hspa Wi-Fi Router with Voice Contact Information