Domain Name Servers DNS | NordicTrack 3G10WV specification

7.4.3Dynamic Route

To activate this option, select the Enabled radio button for Global RIP Mode.

To configure an individual interface, select the desired RIP version and operation, followed by placing a check in the Enabled checkbox for that interface. Click Save/Apply to save the configuration and to start or stop dynamic routing.

7.5Domain Name Servers (DNS)

7.5.1DNS Server Configuration

If the Enable Automatic Assigned DNS checkbox is selected, this device will accept the first received DNS assignment from the Wireless Area Network (WAN) interface during the connection process. If the checkbox is not selected, a field will appear allowing you to enter the primary and optional secondary DNS server IP addresses. Click on Save to apply.

NOTE:

Click the Save button to save the new configuration. To make the new configuration effective, reboot your Router.

3G10WV HSPA Wi-Fi Router with Voice – 57

Image 57

NordicTrack 3G10WV manual Domain Name Servers DNS, DNS Server Configuration

Contents

3G10WV Hspa 7.2 Mbps Wi-Fi Router with Voice Preface Important Notice and Safety Precaution Table of Contents Appendix a Command Line Interface CLI Commands Via Telnet Introduction Introduction Package Contents Features LED Indicators Color Mode DescriptionAssociated port Rear Panel Quick Setup Setup Procedure Quick SetupConfigure the router through the Web User Interface WUI Save the router configuration and reboot see section Web User Interface Web User Interface Default Settings TCP/IP Settings Dhcp ModeClick OK to submit the settings To login to the web interface, follow the steps below Login Procedure Basic / Home Web User Interface Homepage Fields Description Following table provides further details 3G Settings 3G Settings 3G Service SetupThis menu includes 3G service Setup and PIN Configuration 20 3G10WV Hspa Wi-Fi Router with Voice PIN Configuration PIN Code ProtectionPIN Lock Off PIN Lock On PIN Code Change Wireless Wireless Option Description Setup Security Click Save/Apply to configure the wireless security options Authentication Card. If the Ssid does not match, access is deniedWEP Encryption will also be enabled Select Ssid Configuration Default is disabled Broadcast and multicast messages. The default isAP Isolation Point can be linked Only mode 54g ModeMbit/s Dsss specification as described in Ieee Std 54g Protection MAC Filter Deny Rejects access for the specified MAC addressesMAC Address Can be added Wireless Bridge Click Save/Apply to implement new configuration settingsFeature Options Station Info Authorized Lists those devices with authorized accessIs generated randomly Associated Management Management Device Settings Restore Default Update Settings 38 3G10WV Hspa Wi-Fi Router with Voice Setting up Snmp agent Configure Snmp agent on 3G10WVBy default, Snmp agent is enabled on the gateway Press Save/Apply to activate setting Simple Network Time Protocol Sntp Access Control 42 3G10WV Hspa Wi-Fi Router with Voice Save and Reboot Advanced Setup This chapter explains advanced setup for your Router Advanced Setup These options are used for special Dhcp set up Setting. By default NAT is enabledHosts connected to Hspa 7.2 Mbps Wi-Fi Router Local Area Network LAN Enable Dhcp Server Enable DhcpShow up on the same page as below Server Relay Port Forwarding Network Address Translation NAT Selected the port ranges are automatically configured Is selected the port ranges are automatically configuredOptions Description External Port End Port Triggering Trigger Port End Demilitarized DMZ HostTrigger Protocol TCP, TCP/UDP or UDP Open Port Start Open Port End 52 3G10WV Hspa Wi-Fi Router with Voice Options Description Parental Control User Name User-defined label for this restrictionMAC address of the PC running the browser Routing 56 3G10WV Hspa Wi-Fi Router with Voice Domain Name Servers DNS DNS Server Configuration Options Descriptions Dynamic DNS Voice Voice Configuring your 3G10WV for placing Voice Calls Status Status Test Description Diagnostics System Log Click View System Log. The results are displayed as follows 3G Status Status Description Status Status BCS Battery Charge LevelQuality Ec/Io Strongest cells Network Registration Interface Shows connection interfaces Statistics Service Shows the service type Select Route to display the paths the Router has found RouteField Description But may be needed by routing daemons ARP Dynamic Host Configuration Protocol DhcpClick ARP to display the ARP information Click Dhcp to display the Dhcp information Ping CLI commands Via Telnet Help CLI commands via TelnetEnd the telnet session Synopsis help ? Example Examples Description Display the 3G network connection status Description Display the Imsi and Imei value Wcdma L1 StateL1MFACH RRC State Cellfach RX level dBm-90Sierra show --mode Sierra show --hsdcat !HSDCAT Sierra show --mode mode Umts Example Set the Custom APN to test.testSynopsis sierra set --apn profile apn profile 1 Custom APN Synopsis sierra set --comp profile type enabledisable Example Enable the IP header compression for Custom APNSierra show -auth 1 Profile1 PAP Connect / Disconnect PPP session PIN code configuration Sierra set --PIN-CHG 0000 Synopsis sierra show --PIN-LOCK ExampleChanged the PIN code successfully PUK code unlock Sierra set --PUK 11111111 0000 PUK unlock successfully Wlan Options Enable Description Set the wireless LAN channel Valid value 0~14 Means auto select channel. Default valueValid value 32 characters string --country countryStr Default value 2346 --dtim dtimInterval Default value 0 --mrate rateVal Example Default value long Options Example Synopsis Configure wireless LAN MAC filterRemove MACaddress Options Description add one MAC Address entry --remove MACaddress Description set remote bridge MAC address Wlan security wpaGTKRekey = Advance Wlan security WepCurrentKeyindex = 1 --macfilter 92 3G10WV Hspa Wi-Fi Router with Voice Wlan info --config --security --macfilter --wds --station Scenario 6 to configure AP with WPA2 security 3G10WV Hspa Wi-Fi Router with Voice Contact Information