54g Mode, Only mode, 54g Protection | NordicTrack 3G10WV instruction

Option	Description

54g Mode	Select Auto mode for greatest compatibility. Select Performance mode for the fastest
	performance among 54g certified equipment. Select LRS mode if you are experiencing
	difficulty with legacy 802.11b equipment. If this does not work, you may also try 802.11b
	only mode.

54g Protection	In Auto mode, the router will use RTS/CTS to improve 802.11g performance in mixed
	802.11g/802.11b networks. Turning protection Off will maximize 802.11g throughput
	under most conditions.

Preamble Type	Short preamble is intended for applications where maximum throughput is desired but
	it does not work with legacy equipment. Long preamble works with the current 1 and 2
	Mbit/s DSSS specification as described in IEEE Std 802.11-1999

Transmit Power	Set the power output (by percentage) as desired.

3G10WV HSPA Wi-Fi Router with Voice – 31

Image 31

NordicTrack 3G10WV manual 54g Mode, Only mode, 54g Protection, Under most conditions, Preamble Type

Contents

3G10WV Hspa 7.2 Mbps Wi-Fi Router with Voice Preface Important Notice and Safety Precaution Table of Contents Appendix a Command Line Interface CLI Commands Via Telnet Introduction Introduction Package Contents Features Color Mode Description LED IndicatorsAssociated port Rear Panel Quick Setup Save the router configuration and reboot see section Quick SetupSetup Procedure Configure the router through the Web User Interface WUI Web User Interface Web User Interface Default Settings Dhcp Mode TCP/IP SettingsClick OK to submit the settings To login to the web interface, follow the steps below Login Procedure Basic / Home Web User Interface Homepage Fields Description Following table provides further details 3G Settings 3G Service Setup 3G SettingsThis menu includes 3G service Setup and PIN Configuration 20 3G10WV Hspa Wi-Fi Router with Voice PIN Code Protection PIN ConfigurationPIN Lock Off PIN Lock On PIN Code Change Wireless Wireless Option Description Setup Security Click Save/Apply to configure the wireless security options Select Ssid Card. If the Ssid does not match, access is deniedAuthentication WEP Encryption will also be enabled Configuration Point can be linked Broadcast and multicast messages. The default isDefault is disabled AP Isolation 54g Protection 54g ModeOnly mode Mbit/s Dsss specification as described in Ieee Std Can be added Deny Rejects access for the specified MAC addressesMAC Filter MAC Address Click Save/Apply to implement new configuration settings Wireless BridgeFeature Options Associated Authorized Lists those devices with authorized accessStation Info Is generated randomly Management Management Device Settings Restore Default Update Settings 38 3G10WV Hspa Wi-Fi Router with Voice Press Save/Apply to activate setting Configure Snmp agent on 3G10WVSetting up Snmp agent By default, Snmp agent is enabled on the gateway Simple Network Time Protocol Sntp Access Control 42 3G10WV Hspa Wi-Fi Router with Voice Save and Reboot Advanced Setup This chapter explains advanced setup for your Router Advanced Setup Local Area Network LAN Setting. By default NAT is enabledThese options are used for special Dhcp set up Hosts connected to Hspa 7.2 Mbps Wi-Fi Router Server Relay Enable DhcpEnable Dhcp Server Show up on the same page as below Port Forwarding Network Address Translation NAT External Port End Is selected the port ranges are automatically configuredSelected the port ranges are automatically configured Options Description Port Triggering Open Port End Demilitarized DMZ HostTrigger Port End Trigger Protocol TCP, TCP/UDP or UDP Open Port Start 52 3G10WV Hspa Wi-Fi Router with Voice Options Description User Name User-defined label for this restriction Parental ControlMAC address of the PC running the browser Routing 56 3G10WV Hspa Wi-Fi Router with Voice Domain Name Servers DNS DNS Server Configuration Options Descriptions Dynamic DNS Voice Voice Configuring your 3G10WV for placing Voice Calls Status Status Test Description Diagnostics System Log Click View System Log. The results are displayed as follows 3G Status Status Description Strongest cells Network Registration Status BCS Battery Charge LevelStatus Quality Ec/Io Interface Shows connection interfaces Statistics Service Shows the service type But may be needed by routing daemons RouteSelect Route to display the paths the Router has found Field Description Click Dhcp to display the Dhcp information Dynamic Host Configuration Protocol DhcpARP Click ARP to display the ARP information Ping CLI commands Via Telnet Synopsis help ? Example CLI commands via TelnetHelp End the telnet session Examples Description Display the 3G network connection status Sierra show --hsdcat !HSDCAT Wcdma L1 StateL1MFACH RRC State Cellfach RX level dBm-90Description Display the Imsi and Imei value Sierra show --mode Example Set the Custom APN to test.test Sierra show --mode mode UmtsSynopsis sierra set --apn profile apn profile 1 Custom APN Example Enable the IP header compression for Custom APN Synopsis sierra set --comp profile type enabledisableSierra show -auth 1 Profile1 PAP Connect / Disconnect PPP session PIN code configuration Sierra set --PUK 11111111 0000 PUK unlock successfully Synopsis sierra show --PIN-LOCK ExampleSierra set --PIN-CHG 0000 Changed the PIN code successfully PUK code unlock Wlan Options Enable Means auto select channel. Default value Description Set the wireless LAN channel Valid value 0~14Valid value 32 characters string --country countryStr Default value 2346 --dtim dtimInterval Default value 0 --mrate rateVal Example Default value long Options Example Description add one MAC Address entry --remove MACaddress Configure wireless LAN MAC filterSynopsis Remove MACaddress Options Description set remote bridge MAC address Wlan security wpaGTKRekey = Advance Wlan security WepCurrentKeyindex = 1 --macfilter 92 3G10WV Hspa Wi-Fi Router with Voice Wlan info --config --security --macfilter --wds --station Scenario 6 to configure AP with WPA2 security 3G10WV Hspa Wi-Fi Router with Voice Contact Information